Nissan Rogue. Manual — part 244
DAS
C1A17 DISTANCE SENSOR
DAS-147
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1A17 DISTANCE SENSOR
DTC Logic
INFOID:0000000011277305
DTC DETECTION LOGIC
NOTE:
If DTC C1A17 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
106, "DISTANCE SENSOR : DTC Logic"
.
Diagnosis Procedure
INFOID:0000000011277306
1.
REPLACE DISTANCE SENSOR
>> Replace distance sensor. Refer to
DAS-170, "Removal and Installation"
.
CONSULT Display
DTC detecting condition
Possible causes
LASER SENSOR FAIL
[C1A17]
Distance sensor is malfunctioning.
Distance sensor.
DAS-148
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C1A18 RADAR AIMING INCMP
C1A18 RADAR AIMING INCMP
DTC Logic
INFOID:0000000011277307
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM SELF DIAGNOSTIC RESULT
1. Start the engine.
2. Perform “Self Diagnostic Result” of “LASER/RADAR” using CONSULT.
Is DTC detected?
YES
>> Refer to
DAS-148, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011277308
1.
ADJUST DISTANCE SENSOR
Perform Distance Sensor Initial Vertical Alignment and Distance Sensor Alignment.
>> Refer to
.
CONSULT Display
DTC Detection Condition
Possible Cause
LASER AIMING INCMP
[C1A18]
Distance sensor not adjusted.
• Distance sensor aiming adjustment not per-
formed.
• Distance sensor aiming adjustment interrupt-
ed.
DAS
C1A21 UNIT HIGH TEMP
DAS-149
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1A21 UNIT HIGH TEMP
DTC Logic
INFOID:0000000011277309
DTC DETECTION LOGIC
1.
PERFORM SELF DIAGNOSTIC RESULT
1. Turn ignition switch OFF.
2. Wait for 10 minutes or more to cool the distance sensor.
3. Start the engine.
4. Perform “Self Diagnostic Result” of “LASER/RADAR” using CONSULT.
Is DTC detected?
YES
>> Replace distance sensor. Refer to
DAS-170, "Removal and Installation"
.
NO
>> Refer to
GI-44, "Intermittent Incident"
.
CONSULT Display
DTC detecting condition
Possible causes
UNIT HIGH TEMP
[C1A21]
Distance sensor judges high temperature abnor-
mality.
Temperature around distance sensor high.
DAS-150
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C1A24 NP RANGE
C1A24 NP RANGE
DTC Logic
INFOID:0000000011277310
DTC DETECTION LOGIC
NOTE:
If DTC C1A24 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
106, "DISTANCE SENSOR : DTC Logic"
.
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF DIAGNOSTIC RESULT (1)
1. Start the engine.
2. Shift selector lever to P position and wait for approximately 5 minutes or more.
3. Perform “Self Diagnostic Result” of “LASER/RADAR” using CONSULT.
Is DTC detected?
YES
>> Refer to
DAS-150, "Diagnosis Procedure"
NO
>> GO TO 2.
2.
CHECK SELF DIAGNOSTIC RESULT (2)
1. Shift selector lever to N position and wait for approximately 5 minutes or more.
2. Perform “Self Diagnostic Result” of “LASER/RADAR” using CONSULT.
Is DTC detected?
YES
>> Refer to
DAS-150, "Diagnosis Procedure"
NO
>> Refer to
GI-44, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000011277311
1.
CHECK SELF DIAGNOSTIC RESULT OF TCM
Perform “Self Diagnostic Result” of “TRANSMISSION” using CONSULT.
Are any DTCs detected?
YES
>> Refer to
NO
>> Replace distance sensor. Refer to
DAS-170, "Removal and Installation"
.
CONSULT Display
DTC Detection Condition
Possible Cause
NP RANGE
[C1A24]
A mismatch between shift position signal and a
current gear position signal transmitted from
TCM via CAN communication that continues for
60 seconds or more.
• TCM.
• Transmission range switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст