Nissan Rogue. Manual — part 1053
SE-78
< UNIT DISASSEMBLY AND ASSEMBLY >
SECOND ROW SEAT
1. Remove second row seat RH. Refer to
SE-39, "Removal and Installation"
.
2. Using a suitable tool release clips and remove seatback board.
: Clip
3. Remove screw (A) then using a suitable tool release clips and
pawls and remove seat cushion outer finisher (RH).
: Clip
: Pawl
4. Using a suitable tool release clips and pawls and remove seat
cushion outer finisher (LH).
: Clip
: Pawl
5. Press headrest holder lock button, then lift headrest up and remove.
6. Reach up behind the seatback pad, release the headrest holder
locks as shown and remove the headrest holders.
CAUTION:
Before removing/installing headrest holder, check its orien-
tation (front/rear and right/left).
7. Release pawls and remove recline handle finisher.
8. Release J-hooks then release fasteners and remove seatback pad and seatback trim from seatback
frame.
ALJIA1455ZZ
ALJIA1447ZZ
ALJIA1458ZZ
PIIB4084J
SECOND ROW SEAT
SE-79
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
9. Remove hog rings, then separate seatback trim from seatback
pad.
NOTE:
Remove all pieces of hog rings and discard them.
: Hog ring
10. Remove bolts (A) and seatback frame (1) from seat cushion
frame (2).
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Install new hog rings on the seat cushion trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat
cushion trim and seat cushion pad wires.
• Use NISSAN standard hog rings and tools to assemble.
• Smooth out all wrinkles during assembly.
RH SEAT : Seat Cushion
INFOID:0000000011280477
DISASSEMBLY
1. Remove second row seat RH. Refer to
SE-39, "Removal and Installation"
.
2. Using a suitable tool release clips and remove seatback board.
: Clip
ALJIA1457ZZ
ALJIA1465ZZ
PIIB3356J
ALJIA1455ZZ
SE-80
< UNIT DISASSEMBLY AND ASSEMBLY >
SECOND ROW SEAT
3. Remove screw (A) then using a suitable tool release clip and
pawls and remove seat cushion outer finisher (RH).
: Clip
: Pawl
4. Using a suitable tool release clips and pawls and remove seat
cushion outer finisher (LH) (1).
: Clip
: Pawl
5. Press headrest holder lock button, then lift headrest up and remove.
6. Reach up behind the seatback pad, release the headrest holder
locks as shown and remove the headrest holders.
CAUTION:
Before removing/installing headrest holder, check its orien-
tation (front/rear and right/left).
7. Release pawls and remove recline handle finisher.
8. Release J-hooks then release fasteners and remove seatback pad and seatback trim from seatback
frame.
9. Route seat belt buckle through seat cushion.
10. Release J-hooks and remove the seat cushion pad and seat cushion trim.
11. Remove hog rings, then separate seat cushion trim from seat
cushion pad.
NOTE:
Remove all pieces of hog rings and discard them.
: Hog ring
ASSEMBLY
Assembly is in the reverse order of disassembly.
ALJIA1447ZZ
ALJIA1458ZZ
PIIB4084J
ALJIA1456ZZ
SECOND ROW SEAT
SE-81
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Install new hog rings on the seat cushion trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat
cushion trim and seat cushion pad wires.
• Use NISSAN standard hog rings and tools to assemble.
• Smooth out all wrinkles during assembly.
PIIB3356J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст