Nissan Rogue. Manual — part 131
BCS-130
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
COMBINATION SWITCH INPUT CIRCUIT
Is the inspection result normal?
YES
>> Replace the combination switch. Refer to
BCS-136, "Removal and Installation"
.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
BCS
COMBINATION SWITCH OUTPUT CIRCUIT
BCS-131
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
COMBINATION SWITCH OUTPUT CIRCUIT
Diagnosis Procedure
INFOID:0000000011280280
Regarding Wiring Diagram information, refer to
1.
CHECK OUTPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect BCM connector M19 and combination switch connector.
3. Check continuity between BCM connector M19 and combination switch connector M28.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK OUTPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT
Check continuity between BCM connector M19 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK BCM INPUT VOLTAGE
1. Connect BCM connector M19 and combination switch connector.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M19 and ground.
Combination switch
signal
BCM
Combination switch
Continuity
Connector
Terminal
Connector
Terminal
OUTPUT 1
M19
85
M28
2
Yes
OUTPUT 2
84
10
OUTPUT 3
86
15
OUTPUT 4
87
4
OUTPUT 5
34
7
Combination switch
signal
BCM
Ground
Continuity
Connector
Terminal
OUTPUT 1
M19
85
No
OUTPUT 2
84
OUTPUT 3
86
OUTPUT 4
87
OUTPUT 5
34
Combination switch
signal
BCM
Ground
Voltage
Connector
Terminal
OUTPUT 1
M19
85
—
Refer to
.
OUTPUT 2
84
OUTPUT 3
86
OUTPUT 4
87
OUTPUT 5
34
BCS-132
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
COMBINATION SWITCH OUTPUT CIRCUIT
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Replace the combination switch. Refer to
BCS-136, "Removal and Installation"
.
BCS
COMBINATION SWITCH SYSTEM SYMPTOMS
BCS-133
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000011280281
1. Perform the data monitor of CONSULT to check for any malfunctioning item.
2. Check the malfunction combinations.
Malfunction item:
×
3. Identify the malfunctioning part from the agreed combination and repair or replace the part.
Malfunction combination
Data monitor item
FR WIPE
R HI
F
R
WIPER LOW
FR W
ASHER S
W
FR
W
IP
E
R
I
N
T
IN
T V
O
LU
ME
RR W
IPER ON
R
R
WIPER
IN
T
RR W
ASHER SW
TURN SIGNAL R
T
U
R
N
SIGNAL L
TA
IL LAM
P
SW
HI BEAM
SW
HE
A
D
LA
MP
S
W
LIGHT OFF
SW
P
ASSING SW
A
×
×
B
×
×
×
C
×
×
×
×
D
×
×
×
×
E
×
×
×
F
×
×
×
G
×
×
×
×
H
×
×
×
×
I
×
×
J
×
×
×
K
All Items
L
If only one item is detected or the item is not applicable to the combinations A to K
Malfunction
combination
Malfunctioning part
Repair or replace
A
Combination switch INPUT 1 circuit
Inspect the combination switch input circuit applicable to the malfunctioning
part. Refer to
BCS-129, "Diagnosis Procedure"
.
B
Combination switch INPUT 2 circuit
C
Combination switch INPUT 3 circuit
D
Combination switch INPUT 4 circuit
E
Combination switch INPUT 5 circuit
F
Combination switch OUTPUT 1 circuit
Inspect the combination switch output circuit applicable to the malfunction-
ing part. Refer to
BCS-131, "Diagnosis Procedure"
G
Combination switch OUTPUT 2 circuit
H
Combination switch OUTPUT 3 circuit
I
Combination switch OUTPUT 4 circuit
J
Combination switch OUTPUT 5 circuit
K
BCM
BCS-135, "Removal and Installation"
L
Combination switch
Replace the combination switch. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст