Nissan Rogue. Manual — part 141
BR-34
< REMOVAL AND INSTALLATION >
FRONT DISC BRAKE
FRONT DISC BRAKE
BRAKE PAD (1 PISTON TYPE)
BRAKE PAD (1 PISTON TYPE) : Exploded View
INFOID:0000000011279887
USA Production
AWFIA1112ZZ
1.
Torque member
2.
Bushing
3.
Piston boot
4.
Slide pin boot
5.
Slide pin
6.
Piston
7.
Piston seal
8.
Brake caliper body
9.
Bleeder cap
10. Brake hose
11. Copper sealing washers
12. Inner shim cover
13. Inner shim
14. Inner pad
15. Pad retainer
16. Anti-rattle clip
17. Outer pad
18. Outer shim
19. Outer shim cover
A.
Niglube Rx-2
B.
Rubber grease
C.
Molykote® AS-880N
D.
Molykote® 7439
: Apply brake fluid.
FRONT DISC BRAKE
BR-35
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
Korea Production
BRAKE PAD (1 PISTON TYPE) : Removal and Installation
INFOID:0000000011279888
REMOVAL
WARNING:
Clean dust on brake caliper and brake pad with a vacuum dust collector to minimize the hazards of air-
borne particles or other material.
CAUTION:
• Do not depress the brake pedal while removing the brake pads because the pistons may pop out.
• It is not necessary to remove bolts on torque member and brake hose except for disassembly or
replacement of brake caliper. For brake pad removal, hang brake caliper with a wire so as not to
stretch brake hose.
• If brake fluid or grease adheres to the brake caliper or disc brake rotor, quickly wipe it off.
• Do not reuse drained brake fluid.
1. Observe brake fluid level in reservoir tank. Partially drain brake fluid if necessary. Refer to
2. Remove the front wheels and tires using power tool.
3. Remove slide pin bolts.
4. Remove the front brake caliper from the torque member. Leaving brake hose attached, reposition the
brake caliper aside with wire.
5. Remove the brake pads, shims, shim covers, pad retainers, and anti-rattle clips from the torque member.
AWFIA1129ZZ
1.
Torque member
2.
Bushing
3.
Piston boot
4.
Slide pin boot
5.
Slide pin
6.
Piston
7.
Piston seal
8.
Brake caliper body
9.
Bleeder cap
10. Brake hose
11. Copper sealing washers
12. Inner shim cover
13. Inner shim
14. Inner pad
15. Pad retainer
16. Anti-rattle clip
17. Outer pad
18. Outer shim
19. Outer shim cover
A.
Niglube Rx-2
B.
Rubber grease
C.
Molykote® AS-880N
D.
Molykote® 7439
: Apply brake fluid.
BR-36
< REMOVAL AND INSTALLATION >
FRONT DISC BRAKE
CAUTION:
• Do not reuse the pad retainers and anti-rattle clips.
• Do not damage the piston boot.
• Do not drop the brake pads, shims, or the shim covers.
• Note the position of components during removal to aid with installation.
6. Compress the front caliper piston.
INSTALLATION
1. Install the new pad retainers and anti-rattle clips to the torque member.
CAUTION:
• Do not reuse the pad retainers and anti-rattle clips.
• Do not deform the pad retainers.
• Verify that the pad retainers are secured properly to the torque member.
2. For USA Production apply Molykote® AS-880N grease to the
mating faces between the brake pads (1) and pad retainers.
BR-34, "BRAKE PAD (1 PISTON TYPE) : Exploded
.
3. For USA Production apply Molykote® AS-880N grease to the
mating faces between the brake pads (1), inner shim (2) and
outer shim (3), and install them to the brake pad. Refer to
34, "BRAKE PAD (1 PISTON TYPE) : Exploded View"
.
CAUTION:
When installing new brake pads, replace the shims and
shim covers.
4. For Korea Production, apply Molykote® AS-880N grease to the
mating faces between the brake pads and pad retainers. Refer
BR-34, "BRAKE PAD (1 PISTON TYPE) : Exploded View"
5. For Korea Production, apply Molykote® AS-880N grease to the
mating faces between the brake pads inner shim (1) and outer
shim (2), and install them to the brake pad. Refer to
"BRAKE PAD (1 PISTON TYPE) : Exploded View"
.
CAUTION:
When installing new brake pads, replace the shims and
shim covers.
ALFIA0445ZZ
ALFIA0504ZZ
FRONT DISC BRAKE
BR-37
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
6. Install the brake pads to the torque member.
7. Using a suitable tool, press the piston into the brake caliper.
CAUTION:
Do not damage the piston boot.
8. Install the brake caliper to the torque member.
9. Install the slide pin bolts and tighten to specification. Refer to
BR-34, "BRAKE PAD (1 PISTON TYPE) :
.
10. Depress the brake pedal several times and verify that drag does not exist.
11. Install the front wheels and tires. Refer to
WT-67, "Removal and Installation"
.
12. Check brake fluid level and refill as necessary. Refer to
.
INSPECTION AFTER INSTALLATION
1. Check the drag of front disc brake. If any drag is found, follow the procedure described below.
2. Remove brake pads.
3. Using a suitable tool, press the piston into the brake caliper body.
CAUTION:
Do not damage the piston boots.
4. Install brake pads.
5. Depress the brake pedal several times.
6. Check the drag of front disc brake again. If any drag is found, disassemble the brake caliper body.
7. Burnish contact surfaces after refinishing or replacing disc brake rotors or if a soft pedal occurs at very low
mileage. Refer to
BRAKE CALIPER ASSEMBLY (1 PISTON TYPE)
BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Exploded View
INFOID:0000000011279889
1.
Torque member
2.
Bushing
3.
Piston boot
4.
Slide pin boot
5.
Slide pin
6.
Piston
7.
Piston seal
8.
Brake caliper body
9.
Bleeder cap
AWFIA1112ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст