Nissan Rogue. Manual — part 1262
FRONT WIPER DOES NOT OPERATE
WW-51
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER DOES NOT OPERATE
Description
INFOID:0000000011280407
The front wiper does not operate under any operation conditions.
Diagnosis Procedure
INFOID:0000000011280408
Regarding Wiring Diagram information, refer to
.
1.
CHECK WIPER RELAY OPERATION
CONSULT ACTIVE TEST
1. Select “FR WIPER” in “Active Test” of “BCM (WIPER)”.
2. Check front wiper operation.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK FRONT WIPER MOTOR FUSE
.
Is the fuse blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 3.
3.
CHECK FRONT WIPER MOTOR GROUND CIRCUIT
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK FRONT WIPER MOTOR OUTPUT VOLTAGE
1. Turn the ignition switch ON.
2. Select “FRONT WIPER” in “Active Test” of “IPDM E/R” with CONSULT.
3. Check voltage between IPDM E/R harness connector and ground while wipers are operating.
Is the inspection result normal?
YES
>> Replace front wiper motor. Refer to
WW-69, "Removal and Installation"
NO
>> Replace IPDM E/R. Refer to
PCS-40, "Removal and Installation"
.
5.
CHECK FRONT WIPER REQUEST SIGNAL INPUT
1. Select “FR WIP REQ” in “Data Monitor” of “IPDM E/R” with CONSULT.
2. Switch the front wiper switch to HI and LO.
3. Check the status of FR WIP REQ while operating the switch.
LO
: Front wiper LO operation
HI
: Front wiper HI operation
OFF
: Front wiper stop
IPDM E/R
Ground
FRONT WIPER
Voltage
(Approx.)
Connector
Terminal
E121
48
LO
Battery voltage
OFF
0 V
45
HI
Battery voltage
OFF
0 V
WW-52
< SYMPTOM DIAGNOSIS >
FRONT WIPER DOES NOT OPERATE
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-40, "Removal and Installation"
NO
>> GO TO 6.
6.
CHECK COMBINATION SWITCH (WIPER AND WASHER SWITCH)
Check combination switch (wiper and washer switch). Refer to
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
(with Intelligent Key system) or
135, "Removal and Installation"
(without Intelligent Key system).
NO
>> Repair or replace the applicable parts.
Data monitor
Condition
Status
FR WIP REQ
Front wiper switch OFF
STOP
Front wiper switch LO
LOW
Front wiper switch HI
HI
NORMAL OPERATING CONDITION
WW-53
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
NORMAL OPERATING CONDITION
Description
INFOID:0000000011280409
FRONT WIPER PROTECTION FUNCTION
IPDM E/R detects front wiper stop position by a front wiper stop position signal.
When a front wiper stop position signal is in the conditions listed below, IPDM E/R stops power supply to wiper
after repeating a front wiper 10 seconds activation and 20 seconds stop.
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
REAR WIPER MOTOR PROTECTION FUNCTION
• BCM may stop rear wiper to protect the rear wiper motor when the rear wiper is stopped for 5 seconds or
more due to a snowfall.
• Rear wiper operates normally one minute after the obstacles are removed with rear wiper OFF.
Ignition switch
Front wiper switch
Front wiper stop position signal
ON
OFF
The front wiper stop position signal (stop position) cannot be input for 10 seconds.
ON
The front wiper stop position signal does not change for 10 seconds.
WW-54
< REMOVAL AND INSTALLATION >
WASHER TANK
REMOVAL AND INSTALLATION
WASHER TANK
Exploded View
INFOID:0000000011280410
Removal and Installation
INFOID:0000000011280411
REMOVAL
1. Drain washer fluid.
2. Using a suitable tool release washer tank inlet clip and remove washer tank inlet.
3. Remove front over fender (RH). Refer to
EXT-30, "FRONT OVER FENDER : Removal and Installation"
.
4. Remove wind deflector (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
5. Remove engine side cover (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
6. Partially remove front fender protector (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
7. Disconnect harness connector from rear view camera washer motor then front and rear washer motor.
8. Disconnect washer level switch harness connector (if equipped).
9. Disconnect front and rear washer motor tubes and the rear view camera washer motor tube (if equipped).
10. Remove washer tank nuts and bolt and remove the washer tank.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
1.
Cap
2.
Washer tank
3.
Washer tank inlet
A. Clip
B. Refer to INSTALLATION
Front
AWLIA2500ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст