Nissan Rogue. Manual — part 1177
TM-80
< BASIC INSPECTION >
[CVT: RE0F10D]
DIAGNOSIS AND REPAIR WORK FLOW
Climate con-
ditions
Irrelevant
Weather
Clear
Cloud
Rain
Snow
Others
)
Temperature
Hot
Warm
Cool
Cold
Temperature (Approx.
°C/°F)
Relative humidity
High
Moderate
Low
Transaxle condition
In cold-start
During warm-up (approx.
°C/°F)
After warm-up
Engine speed:
rpm
Road conditions
Urban area
Suburb area
Highway
Mountainous road (uphill or downhill)
Operating condition, etc.
Irrelevant
When engine starts
During idling
During driving
During acceleration
At constant speed driving
During deceleration
During cornering (RH curve or LH curve)
Other conditions
Question sheet
Customer's
name
MR/MS
Registration
number
Initial year
registration
Year
Month
day
Vehicle type
Chassis No.
Storage date
Year
Month
day
Engine
Mileage
km/mile
ADDITIONAL SERVICE WHEN REPLACING TCM
TM-81
< BASIC INSPECTION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ADDITIONAL SERVICE WHEN REPLACING TCM
Description
INFOID:0000000011279296
Always perform the following items when the TCM is replaced.
TCM PROGRAMMING
• Since vehicle specifications are not yet written in a new TCM, it is necessary to write them with CONSULT.
CAUTION:
When replacing TCM, save TCM data on CONSULT before removing TCM.
SAVING AND WRITING OF TCM DATA
• TCM performs accurate control by retrieving data (inherent characteristic value) of each solenoid. For this
reason, it is necessary to save data of current TCM in CONSULT before replacing the TCM. After this, the
saved data must be written in new TCM.
Work Procedure
INFOID:0000000011279297
1.
SAVE TCM DATA (IP CHARACTERISTICS VALUE)
NOTE:
Save necessary data stored in TCM in CONSULT according to the following instructions:
With CONSULT
1. Turn ignition switch OFF and wait for 10 seconds.
2. Turn ignition switch ON.
3. Select “Work Support” in “TRANSMISSION”.
4. Select “READ IP CHARA - REPLACEMENT TCM”.
5. Import data according to the instructions on the CONSULT screen.
>> GO TO 2.
2.
SAVE TCM DATA (VEHICLE SPECIFICATIONS)
With CONSULT
1. Turn ignition switch OFF.
2. Turn ignition switch ON.
3. Select “Re/programming, Configuration”.
4. Select “AT/CVT”.
NOTE:
If “AT/CVT” is not displayed and TCM data cannot be saved on CONSULT, GO TO 3.
5. Select “Programming”.
6. Save TCM data on CONSULT according to the CONSULT display.
>> GO TO 3.
3.
REPLACE TCM
1. Turn ignition switch OFF and wait for 10 seconds.
2. Replace TCM. Refer to
TM-202, "Removal and Installation"
.
>> GO TO 4.
4.
WRITE TCM DATA (VEHICLE SPECIFICATIONS)
With CONSULT
1. Select “Programming”.
2. Perform programming according to the CONSULT display.
>> GO TO 5.
5.
WRITE TCM DATA (IP CHARACTERISTICS VALUE)
NOTE:
Write data saved in CONSULT into a new TCM according to the following instructions:
TM-82
< BASIC INSPECTION >
[CVT: RE0F10D]
ADDITIONAL SERVICE WHEN REPLACING TCM
With CONSULT
1. Turn ignition switch OFF and wait for 10 seconds.
2. Turn ignition switch ON.
3. Select “Work Support” in “TRANSMISSION”.
4. Select “WRITE IP CHARA - REPLACEMENT TCM”.
5. Write data saved in CONSULT in TCM according to the instructions on the CONSULT screen.
>> WORK END
ADDITIONAL SERVICE WHEN REPLACING TRANSAXLE ASSEMBLY
TM-83
< BASIC INSPECTION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ADDITIONAL SERVICE WHEN REPLACING TRANSAXLE ASSEMBLY
Description
INFOID:0000000011279298
Perform the following work after the transaxle assembly is replaced.
WRITING TCM DATA
• TCM performs accurate control by retrieving data (inherent characteristic value) of each solenoid. For this
reason, after replacing transaxle assembly, it is necessary to write new data in TCM.
ERASING OF CVT FLUID DEGRADATION LEVEL DATA
• TCM records the degradation level of the CVT fluid calculated from the vehicle driving status. Therefore, if
the transaxle assembly is replaced, it is necessary to erase the CVT fluid degradation level data recorded by
TCM.
Work Procedure
INFOID:0000000011279299
1.
CHECK THE SERIAL NUMBER
Write down the serial number of new transaxle assembly.
>> GO TO 2.
2.
WRITE TCM DATA (IP CHARACTERISTICS VALUE)
NOTE:
Write data of new solenoid in TCM according to the following instructions:
With CONSULT
CAUTION:
When the work is interrupted, obtain data again from the supplied CD.
1. Shift the selector lever to the P position.
2. Turn ignition switch OFF and wait for 10 seconds.
3. Turn ignition switch ON.
4. Insert the supplied CD into CONSULT.
5. Select “Work Support” in “TRANSMISSION”.
6. Select “WRITE IP CHARA - REPLACEMENT AT/CVT”.
7. Check that the serial number displayed on CONSULT screen and those written in the memo agree.
8. Write data in TCM according to the instructions on the CONSULT screen.
NOTE:
When writing is complete, the shift position indicator of the combination meter displays P.
>> GO TO 3.
3.
ERASE CVT FLUID DEGRADATION LEVEL DATA
JSDIA6075GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст