Nissan Rogue. Manual — part 1242
WT-44
< DTC/CIRCUIT DIAGNOSIS >
C1765, C1766, C1767, C1768 TIRE PRESSURE SENSOR
C1765, C1766, C1767, C1768 TIRE PRESSURE SENSOR
DTC Logic
INFOID:0000000011280518
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011280519
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
When DTC “C1765, C1766, C1767, C1768” is detected, perform ABS system diagnosis.
>> Perform ABS system diagnosis. Refer to
.
DTC
Display Item
Malfunction Detected Condition
Possible Cause
C1765
WHEEL TOP DATA FL
(Wheel top data front left)
Malfunction in the wheel top data from the front LH
wheel speed sensor.
Wheel speed sensor
C1766
WHEEL TOP DATA FR
(Wheel top data front right)
Malfunction in the wheel top data from the front RH
wheel speed sensor.
C1767
WHEEL TOP DATA RR
(Wheel top data rear right)
Malfunction in the wheel top data from the rear RH
wheel speed sensor.
C1768
WHEEL TOP DATA RL
(Wheel top data rear left)
Malfunction in the wheel top data from the rear LH
wheel speed sensor.
C1769 CONFIGURATION SETTING
WT-45
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
C1769 CONFIGURATION SETTING
DTC Logic
INFOID:0000000011280520
This procedure must be performed:
• After replacement of BCM.
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011280521
1.
TIRE PRESSURE MONITORING SYSTEM CONFIGURATION
Perform configuration. Refer to
.
>> GO TO 2.
2.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Does low tire pressure warning lamp turn OFF?
YES
>> Inspection End.
NO
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
(with Intelligent Key system) or
135, "Removal and Installation"
(without Intelligent Key system).
DTC
Display Item
Malfunction detected condition
C1769
CONFIG SETTING
(Configuration setting)
Tire air pressure monitoring system configuration cannot be performed.
Receiver ID registration cannot be performed.
WT-46
< DTC/CIRCUIT DIAGNOSIS >
C1770, C1771, C1772, C1773 G SENSOR
C1770, C1771, C1772, C1773 G SENSOR
DTC Logic
INFOID:0000000011280522
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011280523
1.
REPLACE WHEEL TIRE PRESSURE SENSOR
When DTC “C1770, C1771, C1772, C1773” is detected, replace wheel tire pressure sensor.
>> Replace applicable wheel tire pressure sensor. Refer to
WT-68, "Removal and Installation"
.
DTC
Display Item
Malfunction Detected Condition
Possible Causes
C1770
G SENSOR FL
(G sensor front left)
Malfunction in the G sensor data from front left wheel sensor.
• Tire pressure sensor
• Tire pressure receiver
C1771
G SENSOR FR
(G sensor front right)
Malfunction in the G sensor data from front right wheel sensor.
C1772
G SENSOR RL
(G sensor rear left)
Malfunction in the G sensor data from rear left wheel sensor.
C1773
G SENSOR RR
(G sensor rear right)
Malfunction in the G sensor data from rear right wheel sensor.
U1000 CAN COMM CIRCUIT
WT-47
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000011280524
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit communicates data but selectively reads required data only.
DTC Logic
INFOID:0000000011280525
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION
With CONSULT
1. Drive for several minutes at a speed of 40 km/h (25 MPH) or more.
2. Stop the vehicle.
3. Perform “Self Diagnostic Result” for “AIR PRESSURE MONITOR”.
Is DTC “U1000” detected?
YES
>> Proceed to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280526
LAN-30, "CAN COMMUNICATION SYSTEM : CAN System Specification Chart"
.
DTC
Display item
Malfunction detected condition
Possible cause
U1000
CAN COMM CIRCUIT
BCM is not communicating CAN com-
munication signal for 2 seconds or more.
• CAN communication malfunction
• Malfunction of BCM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст