Nissan Rogue. Manual — part 615
OPTICAL SENSOR
EXL-89
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace harness.
8.
CHECK OPTICAL SENSOR SHORT CIRCUIT
Check continuity between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
(with Intelligent Key system) or
135, "Removal and Installation"
(without Intelligent Key system).
NO
>> Repair or replace harness.
Optical sensor
BCM
Continuity
Connector
Terminal
Connector
Terminal
M13
2
M18
19
Yes
Optical sensor
Ground
Continuity
Connector
Terminal
M13
2
No
EXL-90
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
HAZARD SWITCH
HAZARD SWITCH
Component Function Check
INFOID:0000000011280741
1.
CHECK HAZARD SWITCH SIGNAL BY CONSULT
CONSULT DATA MONITOR
1. Turn ignition switch ON.
2. Select “HAZARD SW” in “Data Monitor” of “BCM (FLASHER)”.
3. With operating the hazard switch, check the monitor status.
Is the inspection result normal?
YES
>> Hazard switch circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000011280742
1.
CHECK HAZARD SWITCH SIGNAL INPUT
1. Turn ignition switch OFF.
2. Disconnect hazard switch connector.
3. Check voltage between hazard switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between hazard switch harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK HAZARD SWITCH SIGNAL SHORT CIRCUIT
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
(with Intelligent Key system) or
135, "Removal and Installation"
(without Intelligent Key system).
NO
>> Repair or replace harness.
Monitor item
Condition
Monitor status
HAZARD SW
Hazard switch
ON
On
OFF
Off
(+)
(
−)
Voltage (Approx.)
Hazard switch
Connector
Terminal
M26
2
Ground
Battery voltage
Hazard switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
M26
2
M18
11
Yes
Hazard switch
Ground
Continuity
Connector
Terminal
M26
2
No
HAZARD SWITCH
EXL-91
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
4.
CHECK HAZARD SWITCH GROUND OPEN CIRCUIT
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace hazard switch. Refer to
EXL-125, "Removal and Installation"
NO
>> Repair or replace harness.
Hazard switch
Ground
Continuity
Connector
Terminal
M26
3
Yes
EXL-92
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
TURN SIGNAL LAMP CIRCUIT
TURN SIGNAL LAMP CIRCUIT
Description
INFOID:0000000011421526
The BCM monitors inputs from the combination switch (lighting and turn signal switch) to determine when to
activate the turn signals. The BCM outputs voltage direction to the left and right turn signals during turn signal
operation or both during hazard warning operation. The BCM sends a turn signal indicator request to the com-
bination meter via the CAN communication lines.
The BCM performs the fast flasher operation (fail-safe) if any bulb or harness of the turn signal lamp circuit is
open.
NOTE:
Turn signal lamp blinks at normal speed when using the hazard warning lamp.
Component Function Check
INFOID:0000000011421527
1.
CHECK TURN SIGNAL LAMP
CONSULT
1. Select “FLASHER” in “Active Test” of “BCM (FLASHER)”.
2. While operating the test items, check that the turn signal lamp blinks.
Is the inspection result normal?
YES
>> Turn signal lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000011421528
Regarding Wiring Diagram information, refer to
1.
CHECK TURN SIGNAL LAMP BULB
Check the applicable lamp bulb to be sure the proper bulb standard is in use and the bulb is not open.
Is the bulb OK?
YES
>> GO TO 2.
NO
>> Replace the bulb.
2.
CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE
1. Turn the ignition switch OFF.
2. Disconnect the front combination lamp harness connector, door mirror harness connector or the side turn
signal harness connector or the rear combination lamp harness connector in question.
3. Turn the ignition switch ON.
4. Operate the turn signal switch.
5. While the turn signal is operating, check the voltage between the front combination lamp harness connec-
tor and ground.
LH
: Turn signal lamps (LH) ON
RH
: Turn signal lamps (RH) ON
Off
: Turn signal lamps OFF
(+)
(
−)
Voltage
(Approx.)
Connector
Terminal
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст