Nissan Rogue. Manual — part 1136
SRC-94
< DTC/CIRCUIT DIAGNOSIS >
B1427 CONFIG SETTING
B1427 CONFIG SETTING
DTC Description
INFOID:0000000011406243
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011406244
1.
PERFORM CONFIGURATION
Perform configuration for air bag diagnosis sensor unit.
>> Refer to
SRC-42, "CONFIGURATION : Description"
.
CONSULT name
DTC
DTC detecting condition
Repair order
CONFIG SETTING
(Configuration setting)
B1427
When errors are detected in the configura-
tion data stored in the air bag diagnosis
sensor unit.
.
U1000 CAN COMM CIRCUIT
SRC-95
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000011279596
CAN (Controller Area Network) is a serial communication system for real time application. It is an on-vehicle
multiplex communication system with high data communication speed and excellent error detection ability.
Many electronic control units are equipped into vehicles, and each control unit shares information and links
with other control units during operation. With CAN communication, control units are connected with two com-
munication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits and receives data but selectively reads required data only. Refer to
COMMUNICATION SYSTEM : CAN Communication Signal Chart"
.
DTC Logic
INFOID:0000000011279597
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM SELF DIAGNOSTIC RESULT
1. Turn ignition switch ON and wait for 7 seconds or more.
2. Using CONSULT, perform “Self Diagnostic Result” of “AIR BAG”.
3. Check if any DTC is displayed in the “Self Diagnostic Result”.
Is DTC detected?
YES
>> Refer to
NO
>> Refer to
GI-44, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000011279598
1.
CHECK CAN COMMUNICATION SYSTEM
Check CAN communication system. Refer to
LAN-17, "Trouble Diagnosis Flow Chart"
.
>> Inspection End.
CONSULT name
DTC
DTC detecting condition
Repair order
CAN COMMUNICATION FAILURE
U1000
When air bag diagnosis sensor unit is not
transmitting or receiving CAN communi-
cation signals for 2 or more seconds.
Refer to
.
SRC-96
< DTC/CIRCUIT DIAGNOSIS >
U1010 CONTROL UNIT (CAN)
U1010 CONTROL UNIT (CAN)
Description
INFOID:0000000011279599
Air bag diagnosis sensor performs self-tests on key ON. If CAN communication failure within control unit is
detected, DTC is set.
DTC Logic
INFOID:0000000011279600
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM SELF DIAGNOSTIC RESULT
1. Turn ignition switch ON.
2. Using CONSULT, perform “Self Diagnostic Result” of “AIR BAG”.
3. Check if DTC is displayed in the “Self Diagnostic Results”.
Is DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011279601
1.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
Replace air bag diagnosis sensor unit. Refer to
SR-26, "Removal and Installation"
.
>> Inspection End.
CONSULT name
DTC
DTC detecting condition
Repair order
CAN CONTROL UNIT FAILURE
U1010
CAN communication error is detected in
control unit.
.
B142X COLLISION DETECTION
SRC-97
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B142X COLLISION DETECTION
Description
INFOID:0000000011279602
DTC B1421 - B1422 COLLISION DETECTION
The air bag diagnosis sensor unit will set this DTC if it has detected a collision which has resulted in a deploy-
ment of one or more air bags or pre-tensioners. If this DTC is detected after a SRS repair, the air bag diagno-
sis sensor unit has not yet been replaced. This DTC can not be erased.
PART LOCATION
SRC-5, "Component Parts Location"
.
DTC Logic
INFOID:0000000011279603
DTC DETECTION LOGIC
With CONSULT
DTC CONFIRMATION PROCEDURE (With CONSULT)
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.
CHECK SELF DIAGNOSTIC RESULT
Check for the DTC on CONSULT.
Is the DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011279604
Refer to Frontal collision:
SR-5, "FOR FRONTAL COLLISION : When SRS is activated in a collision"
"FOR FRONTAL COLLISION : When SRS is not activated in a collision"
OVER COLLISION : When SRS is activated in a collision"
or Side and rollover collision:
AND ROLLOVER COLLISION : When SRS is not activated in a collision"
CONSULT name
DTC
DTC detecting condition
Repair order
FRONTAL COLLISION DETECTION
B1421
Frontal collision detected. Driver and/or
front passenger air bag modules are de-
ployed.
Refer to
SION : When SRS is activated in a colli-
sion"
COLLISION : When SRS is not activated
in a collision"
SIDE COLLISION DETECTION
B1422
Side collision detected. Curtain air bag
module and seat belt pre-tensioner are
deployed.
Refer to
OVER COLLISION : When SRS is acti-
vated in a collision"
or
AND ROLLOVER COLLISION : When
SRS is not activated in a collision"
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст