Nissan Rogue. Manual — part 927

MWI

U1000 CAN COMM CIRCUIT

MWI-55

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

DTC/CIRCUIT DIAGNOSIS

U1000 CAN COMM CIRCUIT

Description

INFOID:0000000011413316

Refer to

LAN-8, "System Description"

.

DTC Logic

INFOID:0000000011279796

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011279797

1.

PERFORM SELF DIAGNOSTIC RESULT

1. Turn ignition switch ON and wait 2 seconds or more.

2. Perform “Self Diagnostic Result” of “METER/M&A” using CONSULT.
Is DTC “U1000” displayed?

YES

>> Refer to

LAN-17, "Trouble Diagnosis Flow Chart"

.

NO

>> Refer to

GI-44, "Intermittent Incident"

.

DTC

CONSULT

Detection Condition

Possible Cause

U1000

CAN COMM CIRC
[U1000]

When combination meter is not transmitting or receiving CAN
communication signals for 2 seconds or more.

CAN communication system

MWI-56

< DTC/CIRCUIT DIAGNOSIS >

U1010 CONTROL UNIT (CAN)

U1010 CONTROL UNIT (CAN)

Description

INFOID:0000000011279798

Initial diagnosis of combination meter.

DTC Logic

INFOID:0000000011279799

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011279800

1.

REPLACE COMBINATION METER

When DTC “U1010” is detected, replace combination meter.

>> Replace combination meter. Refer to

MWI-84, "Removal and Installation"

.

DTC

CONSULT

Detection Condition

Possible Cause

U1010

CONTROL UNIT (CAN)
[U1010]

When detecting error during the initial diagnosis of the CAN controller
of combination meter.

Combination meter

MWI

B2205 VEHICLE SPEED

MWI-57

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

B2205 VEHICLE SPEED

Description

INFOID:0000000011279801

Vehicle speed signal is transmitted from ABS actuator and electric unit (control unit) via CAN communication

line to combination meter.

DTC Logic

INFOID:0000000011279802

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011279803

1.

CHECK COMBINATION METER INPUT SIGNAL

1. Select “METER/M&A” using CONSULT.

2. Select “SPEED METER” in “Data Monitor”.

3. Check the “SPEED METER” value and compare with the speedometer of the combination meter. Speed-

ometer and Data Monitor values should be close.

Is the inspection result normal?

YES

>> Perform “Self Diagnostic Result” of “ABS”. Refer to

BRC-42, "CONSULT Function"

.

NO

>> Replace combination meter. Refer to

MWI-84, "Removal and Installation"

.

DTC

CONSULT

Detection Condition

Possible Cause

B2205

VEHICLE SPEED CIRC
[B2205]

Malfunction is detected when an erroneous
speed signal is received for 2 seconds or more.

• Combination meter
• ABS actuator and electric unit (control unit)

MWI-58

< DTC/CIRCUIT DIAGNOSIS >

B2267 ENGINE SPEED

B2267 ENGINE SPEED

Description

INFOID:0000000011279804

The engine speed signal is transmitted from ECM to the combination meter with CAN communication.

DTC Logic

INFOID:0000000011279805

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011279806

1.

PERFORM SELF-DIAGNOSIS OF ECM

Perform “Self-Diagnostic Result” of “ECM” using CONSULT, and repair or replace malfunctioning parts.

>> Refer to

EC-69, "CONSULT Function"

.

DTC

CONSULT

Detection Condition

Possible Cause

B2267

TACHO METER
[B2267]

ECM continuously transmits abnormal engine
speed signals for 2 seconds or more.

• Crankshaft position sensor (POS)
• ECM