Nissan Rogue. Manual — part 677
FAX-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
FAX
A
B
FAX
N
O
P
CONTENTS
FRONT AXLE
FWD
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Drive Shaft . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tools . . . . . . . . . ....
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
FRONT WHEEL HUB AND KNUCKLE . . . ..
Inspection . . . . . . . . . . . . . . . . ..
FRONT DRIVE SHAFT . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
FRONT WHEEL HUB . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
FRONT DRIVE SHAFT BOOT . . . . . . ...
Exploded View . . . . . . . . . . . . . .
WHEEL SIDE . . . . . . . . . . . . . . . .
WHEEL SIDE : Removal and Installation . . . .
TRANSAXLE SIDE . . . . . . . . . . . . .
TRANSAXLE SIDE : Removal and Installation . ...
FRONT DRIVE SHAFT . . . . . . . . . .
Exploded View (LH) . . . . . . . . . . . . .
Removal and Installation (LH) . . . . . . . . .
Exploded View (RH) . . . . . . . . . . . .
Removal and Installation (RH) . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY .
FRONT DRIVE SHAFT . . . . . . . . . .
Exploded View (LH) . . . . . . . . . . . . .
Disassembly and Assembly (LH) . . . . . . . .
Exploded View (RH) . . . . . . . . . . . .
Disassembly and Assembly (RH) . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Bearing . . . . . . . . . . . . . . .
Drive Shaft . . . . . . . . . . . . . . . ...
AWD
PRECAUTION . . . . . . . . . . . ..
PRECAUTIONS . . . . . . . . . . . . .
Precautions for Drive Shaft . . . . . . . . . ..
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . .
Special Service Tool . . . . . . . . . . . .
Commercial Service Tools . . . . . . . . . ...
FAX-2
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . .
NVH Troubleshooting Chart . . . . . . . . ...
PERIODIC MAINTENANCE . . . . . .
FRONT WHEEL HUB AND KNUCKLE . . . .
Inspection . . . . . . . . . . . . . . . ...
FRONT DRIVE SHAFT . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ...
FRONT WHEEL HUB . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
FRONT DRIVE SHAFT BOOT . . . . . . ...
Exploded View . . . . . . . . . . . . . ....
WHEEL SIDE . . . . . . . . . . . . . . ....
WHEEL SIDE : Removal and Installation . . . ...
TRANSAXLE SIDE . . . . . . . . . . . . ...
TRANSAXLE SIDE : Removal and Installation . ...
FRONT DRIVE SHAFT . . . . . . . . . ..
Exploded View (LH) . . . . . . . . . . . .
Removal and Installation (LH) . . . . . . . . .
Exploded View (RH) . . . . . . . . . . . .
Removal and Installation (RH) . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY ...
FRONT DRIVE SHAFT . . . . . . . . . ..
Exploded View (LH) . . . . . . . . . . . .
Disassembly and Assembly (LH) . . . . . . .
Exploded View (RH) . . . . . . . . . . . .
Disassembly and Assembly (RH) . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Bearing . . . . . . . . . . . . . .
PRECAUTIONS
FAX-3
< PRECAUTION >
[FWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011278616
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precautions for Drive Shaft
INFOID:0000000011278617
Observe the following precautions when disassembling and assembling drive shaft:
• Do not disassemble joint sub-assembly because it is non-overhaul parts.
• Perform work in a location which is as dust-free as possible.
• Clean the parts before disassembling and assembling.
• Prevent the entry of foreign objects during disassembly.
• Reassemble disassembled parts carefully in the correct order. If work is interrupted, a clean cover must be
placed over parts.
• Use paper shop cloths. Fabric shop cloths must not be used because of the danger of lint adhering to parts.
• Clean disassembled parts (except for rubber parts) with kerosene which shall be removed by blowing with
air or wiping with paper shop cloths.
FAX-4
< PREPARATION >
[FWD]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000011278618
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tools
INFOID:0000000011278619
Tool number
(TechMate No.)
Tool name
Description
KV40107300
(
—
)
Boot band crimping tool
Installing boot band
KV40107500
(
—
)
Drive shaft attachment
Removing drive shaft
KV38107900
(
—
)
Protector
Installing drive shaft
a: 32 mm (1.26 in) dia.
ZZA1229D
ZZA1230D
PDIA1183J
Tool name
Description
Ball joint remover
Removing wheel stud
Drive shaft puller
Removing drive shaft joint sub assembly
NT146
JPDIG0152ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст