Nissan Rogue. Manual — part 1230
WCS
WARNING CHIME SYSTEM SYMPTOMS
WCS-49
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SYMPTOM DIAGNOSIS
WARNING CHIME SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000011276489
CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected.
Symptom
Possible cause
Inspection item
The light reminder warning does not sound.
• Harness between BCM and front door switch LH.
• Front door switch LH
• BCM
• Combination meter
Refer to
.
The parking brake release warning contin-
ues sounding or does not sound.
• Harness between combination meter and parking brake switch.
• Parking brake switch
• BCM
• Combination meter
Refer to
.
The seat belt warning continues sounding
or does not sound.
• Harness between combination meter and seat belt buckle switch LH.
• Seat belt buckle switch LH
• BCM
• Combination meter
Refer to
.
Warning chime does not sound at all.
• BCM
• Combination meter
Refer to
.
WCS-50
< SYMPTOM DIAGNOSIS >
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
Description
INFOID:0000000011276490
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
Diagnosis Procedure
INFOID:0000000011276491
1.
CHECK PARKING BRAKE WARNING LAMP
1. Start the engine.
2. Check the operation of the brake warning lamp by operating the parking brake.
Is the inspection result normal?
YES
>> Replace the combination meter. Refer to
MWI-84, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
Check the parking brake switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connector.
3.
CHECK PARKING BRAKE SWITCH UNIT
Check the parking brake switch. Refer to
WCS-46, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace the combination meter. Refer to
MWI-84, "Removal and Installation"
.
NO
>> Replace the parking brake switch. Refer to
Condition
Warning lamp status
Parking brake applied
ON
Parking brake released
OFF
WCS
THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR DOES
NOT SOUND
WCS-51
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
Description
INFOID:0000000011276492
• Seat belt warning does not sound even though driver seat belt is not fastened.
• Seat belt warning sounds even though driver seat belt is fastened.
Diagnosis Procedure
INFOID:0000000011276493
1.
CHECK WARNING CHIME OPERATION
1. Select “BUZZER” of “BCM” using CONSULT.
2. Perform “SEAT BELT WARN TEST” in “Active Test”.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace combination meter. Refer to
MWI-84, "Removal and Installation"
2.
CHECK COMBINATION METER INPUT SIGNAL
Check the combination meter input signal. Refer to
WCS-43, "Component Function Check"
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
(with Intelligent Key system) or
135, "Removal and Installation"
(without Intelligent Key system).
NO
>> GO TO 3.
3.
CHECK SEAT BELT BUCKLE SWITCH LH CIRCUIT
Check the seat belt buckle switch LH circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connector.
4.
CHECK SEAT BELT BUCKLE SWITCH LH
Check the seat belt buckle switch LH. Refer to
WCS-44, "Component Inspection"
Is the inspection result normal?
YES
>> Replace the combination meter. Refer to
MWI-84, "Removal and Installation"
.
NO
>> Replace the seat belt buckle switch LH. Refer to
SB-11, "FRONT SEAT BELT BUCKLE : Removal
.
Component
CONSULT
Condition
Buzzer
SEAT BELT WARN TEST
ON
OFF
WCS-52
< SYMPTOM DIAGNOSIS >
THE LIGHT REMINDER WARNING DOES NOT SOUND
THE LIGHT REMINDER WARNING DOES NOT SOUND
Description
INFOID:0000000011276494
Light reminder warning does not sound even though headlamp is illuminated.
Diagnosis Procedure
INFOID:0000000011276495
1.
CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” of “METER/M&A” using CONSULT and check the “BUZZER” monitor value.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-84, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK FRONT DOOR SWITCH LH SIGNAL CIRCUIT
Check the front door switch LH signal circuit. Refer to
DLK-156, "Diagnosis Procedure"
(with Intelligent Key
system) or
DLK-330, "Diagnosis Procedure"
(without Intelligent Key system).
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connector.
3.
CHECK FRONT DOOR SWITCH LH
Check the front door switch LH. Refer to
DLK-157, "Component Inspection"
(with Intelligent Key system) or
DLK-331, "Component Inspection"
(without Intelligent Key system).
Is the inspection result normal?
YES
>> Replace the BCM. Refer to
BCS-75, "Removal and Installation"
(with Intelligent Key system) or
BCS-135, "Removal and Installation"
(without Intelligent Key system).
NO
>> Replace the front door switch LH. Refer to
DLK-276, "Removal and Installation"
(with Intelligent
Key system) or
DLK-396, "Removal and Installation"
(without Intelligent Key system).
Monitor item
Condition
Status
BUZZER
Under the condition of buzzer input
On
Except above
Off
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст