Nissan Rogue. Manual — part 1011
RF-24
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
>> GO TO 2.
2.
CONFIRM CONCERN
Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
>> GO TO 3.
3.
IDENTIFY THE MALFUNCTIONING SYSTEM WITH SYMPTOM DIAGNOSIS
Use Symptom diagnosis from the symptom inspection result in step 2 and then identify where to start perform-
ing the diagnosis based on possible causes and symptoms.
>> GO TO 4.
4.
PERFORM THE COMPONENT DIAGNOSIS OF THE APPLICABLE SYSTEM
Perform the diagnosis with Component diagnosis of the applicable system.
>> GO TO 5.
5.
REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 6.
6.
FINAL CHECK
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 2.
Are the malfunctions corrected?
YES
>> Inspection End.
NO
>> GO TO 3.
INSPECTION AND ADJUSTMENT
RF-25
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000011280132
INITIALIZATION PROCEDURE
Moonroof
If the moonroof does not open or close automatically, use the following procedure to return moonroof opera-
tion to normal:
1. Turn ignition switch ON.
2. Push and hold the moonroof switch forward until the moonroof and sunshade stop and bounce back.
3. Release the moonroof switch.
4. Press and hold the moonroof switch within 6 seconds.
5. The roof glass and shade will move to full open and back to full close.
6. Release the switch, initialization is complete if the moonroof operates normally.
ANTI-PINCH FUNCTION
Moonroof/Sunshade
1. Fully open the moonroof to the full open position.
2. Place a piece of wood at the fully closed position.
3. Close the moonroof completely with auto-slide close function.
4. Moonroof should make contact and then tilt up or travel in reverse.
CAUTION:
• Do not test the anti-pinch function with your hands or other body parts because they may be
pinched.
• Depending on the environment and driving conditions, if a similar impact or load is applied to the
moonroof it may lower.
• Test the auto-slide operation before inspection when the initialization procedure is performed.
• Perform the initialization procedure when the auto-slide operation or anti-pinch function does not
operate normally.
RF-26
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis
Procedure
INFOID:0000000011382158
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSE
Check that the following fuse is not blown.
Is the fuse blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1. Disconnect BCM connector M20.
2. Check voltage between BCM connector M20 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM connector M20 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connectors.
BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM) : Diag-
nosis Procedure
INFOID:0000000011382159
Regarding Wiring Diagram information, refer to
1.
CHECK FUSE
Terminal No.
Signal name
Fuse No.
161
BCM power supply
7 (10A)
BCM
Ground
Voltage
(Approx.)
Connector
Terminal
M20
161
—
Battery voltage
BCM
Ground
Continuity
Connector
Terminal
M20
170
—
Yes
171
POWER SUPPLY AND GROUND CIRCUIT
RF-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
Check that the following fuse is not blown.
Is the fuse blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1. Disconnect BCM connector M20.
2. Check voltage between BCM connector M20 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM connector M20 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connectors.
MOONROOF MOTOR ASSEMBLY
MOONROOF MOTOR ASSEMBLY : Description
INFOID:0000000011280135
• BCM supplies the moonroof motor assembly with power.
• CPU is integrated in moonroof motor assembly.
• Tilts up/down & slides open/close by moonroof switch operation.
• In order to close the moonroof during high speed driving, the Combination meter will send a speed signal to
the moonroof CPU to adjust the torque of the motor during the tilt-down operation.
MOONROOF MOTOR ASSEMBLY : Component Function Check
INFOID:0000000011280136
1.
CHECK MOONROOF MOTOR FUNCTION
Does the tilt up/down & slide open/close functions operate normally with moonroof switch?
Is the inspection result normal?
YES
>> Moonroof motor assembly is OK.
NO
>> Refer to
RF-27, "MOONROOF MOTOR ASSEMBLY : Diagnosis Procedure"
MOONROOF MOTOR ASSEMBLY : Diagnosis Procedure
INFOID:0000000011280137
Regarding Wiring Diagram information, refer to
Terminal No.
Signal name
Fuse No.
161
BCM power supply
7 (10A)
BCM
Ground
Voltage
(Approx.)
Connector
Terminal
M20
161
—
Battery voltage
BCM
Ground
Continuity
Connector
Terminal
M20
170
—
Yes
171
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст