Nissan Rogue. Manual — part 81
AV-316
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITH BOSE]
U1265 BOSE AMP.
U1265 BOSE AMP.
DTC Logic
INFOID:0000000011276982
Diagnosis Procedure
INFOID:0000000011276983
Regarding Wiring Diagram information, refer to
.
1.
CHECK CONTINUITY BETWEEN AV CONTROL UNIT AND BOSE SPEAKER AMP.
1. Turn ignition switch OFF.
2. Disconnect AV control unit connector M108 and Bose speaker amp. connector B138.
3. Check continuity between AV control unit connector M108 and Bose speaker amp. connector B138.
4. Check continuity between AV control unit connector M108 and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK AV CONTROL UNIT VOLTAGE
1. Connect AV control unit connector M108.
2. Turn ignition switch ON.
3. Check voltage between AV control unit connector M108 and ground.
Is the inspection result normal?
YES
>> Replace Bose speaker amp. Refer to
AV-372, "Removal and Installation"
NO
>> Replace AV control unit. Refer to
AV-369, "Removal and Installation"
.
CONSULT Display
DTC Detection Condition
Possible Cause
AMP ON TERMINAL
[U1265]
Open or short to ground is detected in BOSE
amp. ON signal circuit.
Open or short to ground in BOSE amp. ON signal
circuit.
AV control unit
Bose speaker amp.
Continuity
Connector
Terminal
Connector
Terminal
M108
1
B138
31
Yes
AV control unit
Ground
Continuity
Connector
Terminal
M108
1
—
No
AV control unit
Ground
Voltage
(Approx.)
(+)
(–)
Connector
Terminal
M108
1
—
Battery voltage
AV
U12AA CONFIGURATION ERROR
AV-317
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITH BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U12AA CONFIGURATION ERROR
DTC Logic
INFOID:0000000011276984
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011276985
1.
PERFORM CONFIGURATION
When U12AA is detected, configuration data must be written.
>> Write configuration data with CONSULT. Refer to
AV-280, "CONFIGURATION (AV CONTROL
CONSULT Display
DTC Detection Condition
Possible Cause
Configuration Error
[U12AA]
AV control unit is not properly configured or con-
figuration is corrupt.
Configuration data needs to be written.
Refer to
AV-318
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITH BOSE]
U12AB ANTENNA
U12AB ANTENNA
DTC Logic
INFOID:0000000011276986
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011276987
Regarding Wiring Diagram information, refer to
.
1.
AM-FM ANTENNA INSPECTION
Visually inspect the antenna base (AM-FM antenna) and antenna feeder. Refer to
.
Is inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning components.
2.
CHECK CONTINUITY BETWEEN AV CONTROL UNIT AND ANTENNA BASE
1. Turn ignition switch OFF.
2. Disconnect AV control unit connector M139 and antenna base connector M502.
3. Check continuity between AV control unit connector M139 and antenna base connector M502.
4. Check continuity between AV control unit connector M139 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK AV CONTROL UNIT VOLTAGE
1. Connect AV control unit connector M139.
2. Turn ignition switch ON.
3. Check voltage between AV control unit connector M139 and ground.
Is the inspection result normal?
YES
>> Replace antenna base. Refer to
AV-385, "Removal and Installation"
.
NO
>> Replace AV control unit. Refer to
AV-369, "Removal and Installation"
.
CONSULT Display
DTC Detection Condition
Possible Cause
FM Antenna error
[U12AB]
Open or short to ground is detected in AM-FM an-
tenna connection.
• AM-FM antenna disconnection.
• Open or short to ground in AM-FM antenna
signal circuit.
AV control unit
Antenna base
Continuity
Connector
Terminal
Connector
Terminal
M139
52
M502
2
Yes
AV control unit
Ground
Continuity
Connector
Terminal
M139
52
—
No
AV control unit
Ground
Voltage
(Approx.)
Connector
Terminal
M139
52
—
Battery voltage
AV
U12AC AV CONTROL UNIT
AV-319
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITH BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U12AC AV CONTROL UNIT
DTC Logic
INFOID:0000000011276988
DTC DETECTION LOGIC
CONSULT Display
DTC Detection Condition
Possible Cause
Display Temperature too High
[U12AC]
Display temperature has exceeded maximum
temperature. Display is switched OFF to avoid ir-
reversible damage.
Replace AV control unit if malfunction occurs
constantly.
Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст