Nissan Rogue. Manual — part 318
DLK-114
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2409 HALF LATCH SWITCH
B2409 HALF LATCH SWITCH
DTC Logic
INFOID:0000000011278825
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Operate automatic back door.
3. Check “Self Diagnostic Result” of “AUTO BACK DOOR” using CONSULT.
Is DTC detected?
YES
>> Refer to
DLK-114, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011278826
Regarding Wiring Diagram information, refer to
.
1.
CHECK FOR FOREIGN MATERIALS IN BACK DOOR LOCK ASSEMBLY
Check for entry of foreign materials in back door lock assembly.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Remove foreign materials.
2.
CHECK BACK DOOR OPEN/CLOSE OPERATION
Manually check open and close operation of back door.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunction parts.
3.
CHECK HALF LATCH SWITCH MONITOR ITEM
1. Select “AUTO BACK DOOR” using CONSULT.
2. Select “HALF LATCH SW” in “Data Monitor”.
3. Check that the function operates normally according to the following conditions:
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 4.
4.
CHECK HALF LATCH SWITCH INPUT SIGNAL
DTC
CONSULT display
description
DTC detecting condition
Possible cause
B2409
HALF LATCH SW
Automatic back door control module detects a mal-
function of half latch switch during automatic oper-
ation of back door.
• Entry of foreign materials to back
door lock assembly
• Back door mechanism
• Automatic back door control mod-
ule
• Half latch switch
• Harness or connectors
Monitor item
Condition
Status
HALF LATCH SW
Back door
Fully closed/Half latch
OFF
Open
ON
2015 Rogue NAM
B2409 HALF LATCH SWITCH
DLK-115
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1. Turn ignition switch OFF.
2. Disconnect back door lock assembly connector.
3. Check voltage between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
CHECK HALF LATCH SWITCH CIRCUIT
1. Disconnect automatic back door control module connector.
2. Check continuity between automatic back door control module harness connector and back door lock
assembly harness connector.
3. Check continuity between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control module. Refer to
DLK-283, "Removal and Installation"
.
NO
>> Repair or replace harness.
6.
CHECK HALF LATCH SWITCH GROUND CIRCUIT
Check continuity between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness or connector.
7.
CHECK HALF LATCH SWITCH
DLK-115, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Replace back door lock assembly. Refer to
DLK-270, "DOOR LOCK : Removal and Installation"
8.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> Inspection End.
Component Inspection
INFOID:0000000011278827
COMPONENT INSPECTION
(+)
(–)
Voltage
(Approx.)
Back door lock assembly
Connector
Terminal
D512
6
Ground
Battery voltage
Automatic back door control module
Back door lock assembly
Continuity
Connector
Terminal
Connector
Terminal
B55
3
D512
6
Yes
Automatic back door control module
Ground
Continuity
Connector
Terminal
B55
3
No
Back door lock assembly
Ground
Continuity
Connector
Terminal
D512
8
Yes
2015 Rogue NAM
DLK-116
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2409 HALF LATCH SWITCH
1.
CHECK SWITCH
1. Turn ignition switch OFF.
2. Disconnect back door lock assembly connector.
3. Check continuity between back door lock assembly terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace back door lock assembly. Refer to
DLK-270, "DOOR LOCK : Removal and Installation"
Back door lock assembly
Condition
Continuity
Terminal
4
8
Back door lock
Open
Yes
Fully closed/Half latch
No
5
Fully close
Yes
Open/Half latch
No
6
Open
Yes
Fully closed/Half latch
No
7
Back door
switch
On
Yes
Off
No
2015 Rogue NAM
B2416 TOUCH SENSOR RH
DLK-117
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
B2416 TOUCH SENSOR RH
DTC Logic
INFOID:0000000011278828
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check “Self Diagnostic Result” of “AUTO BACK DOOR” using CONSULT.
Is DTC detected?
YES
>> Refer to
DLK-117, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011278829
Regarding Wiring Diagram information, refer to
.
1.
CHECK INSTALLATION OF TOUCH SENSOR RH
Check that touch sensor RH is installed normally.
DLK-271, "TOUCH SENSOR : Removal and Installation"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
DLK-271, "TOUCH SENSOR : Removal and Installation"
.
2.
CHECK TOUCH SENSOR MONITOR ITEM
1. Select “AUTO BACK DOOR” using CONSULT.
2. Select “TOUCH SEN RH” in “Data Monitor”.
3. Check that the function operates normally according to the following conditions:
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 3.
3.
CHECK TOUCH SENSOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between touch sensor RH harness connector and automatic back door control module har-
ness connector.
DTC
CONSULT display
description
DTC detecting condition
Possible cause
B2416
TOUCH SEN R
OPEN
Automatic back door control module detects a mal-
function of touch sensor RH during automatic oper-
ation of back door.
• Improper installation of touch sen-
sor
• Touch sensor RH
• Harness or connectors
• Automatic back door control mod-
ule
Monitor item
Condition
Status
TOUCH SEN RH
Touch sensor RH
Other than below
OFF
Detect obstruction
ON
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст