Nissan Rogue. Manual — part 115
BCS-66
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
U0415 VEHICLE SPEED SIG
U0415 VEHICLE SPEED SIG
Description
INFOID:0000000011280218
U0415 is displayed if any unusual condition is present in the reception status of the vehicle speed signal from
the ABS actuator and electric unit (control unit).
DTC Logic
INFOID:0000000011280219
DTC DETECTION LOGIC
NOTE:
• If DTC U0415 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC U0415 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
DTC CONFIRMATION
1. Erase the DTC.
2. Turn ignition switch OFF.
3. Perform “Self Diagnostic Result” of “BCM” with CONSULT, after the ignition switch has been turned ON for
2 seconds or more.
Is any DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280220
1.
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF DIAGNOSTIC RESULT
Perform “Self Diagnostic Result” of “ABS” with CONSULT. Refer to
.
Is any DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 2.
2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND
CIRCUIT
Check ABS actuator and electric unit (control unit) power and ground. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
COMBINATION METER SELF DIAGNOSTIC RESULT
Perform “Self Diagnostic Result” of “METER M&A” with CONSULT. Refer to
Is any DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> Refer to
GI-44, "Intermittent Incident"
.
CONSULT Display
DTC Detection Condition
Possible Cause
VEHICLE SPEED SIG
[U0415]
When the vehicle speed signal received from the
ABS actuator and electric unit (control unit) remains
abnormal for 2 seconds or more.
• ABS system
• Combination meter system
• CAN bus harness
BCS
B2562 LOW VOLTAGE
BCS-67
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
B2562 LOW VOLTAGE
DTC Logic
INFOID:0000000011280221
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC CONFIRMATION
1. Erase DTC.
2. Turn ignition switch OFF.
3. Perform the “Self Diagnostic Result” of “BCM” with CONSULT, after the ignition switch has been turned
ON for 120 seconds or more.
Is any DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280222
1.
CHECK BATTERY VOLTAGE
Check battery voltage.
Is battery voltage less than 8.8V?
YES
>> Charge battery and retest. Refer to
CHG-11, "Work Flow (With EXP-800 NI or GR8-1200 NI)"
CHG-14, "Work Flow (Without EXP-800 NI or GR8-1200 NI)"
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
BCM SELF DIAGNOSTIC RESULT
Perform “Self Diagnostic Result” of “BCM” with CONSULT. Refer to
BCS-24, "BCM : CONSULT Function
Is DTC B2562 CRNT?
YES
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
NO
>> Refer to
GI-44, "Intermittent Incident"
.
CONSULT Display
DTC Detection Condition
Possible cause
LOW VOLTAGE
[B2562]
When the power supply voltage to BCM remains less
than 8.8V for 120 seconds or more.
• Harness or connector (power supply circuit)
• Vehicle battery
BCS-68
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000011280223
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSE
Check that the following fuse is not blown.
Is the fuse blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1. Disconnect BCM connector M20.
2. Check voltage between BCM connector M20 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM connector M20 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connectors.
Terminal No.
Signal name
Fuse No.
161
BCM power supply
7 (10A)
BCM
Ground
Voltage
(Approx.)
Connector
Terminal
M20
161
—
Battery voltage
BCM
Ground
Continuity
Connector
Terminal
M20
170
—
Yes
171
BCS
COMBINATION SWITCH INPUT CIRCUIT
BCS-69
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
COMBINATION SWITCH INPUT CIRCUIT
Diagnosis Procedure
INFOID:0000000011280224
Regarding Wiring Diagram information, refer to
.
1.
CHECK INPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect BCM connector M18 and combination switch connector.
3. Check continuity between BCM connector M18 and combination switch connector M28.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK INPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT
Check continuity between BCM connector M18 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK BCM OUTPUT VOLTAGE
1. Connect BCM connector M18 and combination switch connector.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M18 and ground.
Combination switch
signal
BCM
Combination switch
Continuity
Connector
Terminal
Connector
Terminal
INPUT 1
M18
38
M28
8
Yes
INPUT 2
39
6
INPUT 3
36
5
INPUT 4
37
3
INPUT 5
33
1
Combination switch
signal
BCM
Ground
Continuity
Connector
Terminal
INPUT 1
M18
38
No
INPUT 2
39
INPUT 3
36
INPUT 4
37
INPUT 5
33
Combination switch
signal
BCM
Ground
Voltage
Connector
Terminal
INPUT 1
M18
38
—
Refer to
.
INPUT 2
39
INPUT 3
36
INPUT 4
37
INPUT 5
33
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст