Nissan Rogue. Manual — part 1108
SPIRAL CABLE
SR-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SPIRAL CABLE
Exploded View
INFOID:0000000011279756
Removal and Installation
INFOID:0000000011279757
WARNING:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
• Do not use the air tools or electric tools for servicing.
REMOVAL
1. Disconnect the negative and positive battery terminals, then wait at least three minutes. Refer to
2. Remove the steering wheel. Refer to
ST-11, "Removal and Installation"
.
3. Remove the steering column upper and lower cover. Refer to
IP-18, "Removal and Installation"
4. Disconnect harness connectors (A).
5. Remove screws (A) and then remove spiral cable (1).
ALHIA0359ZZ
1.
Combination switch
2.
Steering angle sensor
3.
Spiral cable
ALHIA0351ZZ
ALHIA0350ZZ
SR-16
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
CAUTION:
• Do not strike or drop the spiral cable.
• Do not turn the spiral cable quickly or beyond the limit
number of turns (approximately 2.5 turns from the neutral
position), this may cause the cable to snap.
• Replace the spiral cable if it has been dropped or sus-
tained an impact.
• Do not disassemble the spiral cable.
• Do not allow oil, grease, detergent, or water to come in
contact with the spiral cable.
INSTALLATION
Installation is in the reverse order of removal.
• The turn signal lever must be in the neutral position for spiral cable installation.
• Set the spiral cable neutral position by carefully turning the spiral
cable clockwise to the end position. Turn the spiral cable counter-
clockwise 2.5 turns stopping when the locating pin (B) is at the top
most position and confirm that a yellow indicator with a vertical
black line will be shown in the window (A).
NOTE:
If a new service part is installed, the neutral position is already set
with a stopper clip in place and should not be adjusted after the
stopper clip is removed. Make sure the stopper is removed before
installing the steering wheel.
• During steering wheel installation, make sure the locating pin hole
is aligned with the locating pin (B) of the spiral cable.
• Adjust the neutral position of the steering angle sensor. Refer to
CAUTION:
• The spiral cable may snap during steering operation if the spiral cable is installed in an improper
position.
• Do not overturn the spiral cable or go beyond the maximum number of turns allowed. This will cause
the cable to snap.
• The turn signal lever must be in the neutral position for spiral cable installation.
• Do not apply lubricant to the spiral cable.
• Do not allow oil, grease, detergent or water to come in contact with the spiral cable.
• After installation is complete, check that no system malfunction is detected causing the air bag
warning lamp to illuminate.
• If a malfunction is indicated by the air bag warning lamp after repair or replacement of the malfunc-
tioning parts, perform the SRS Final Check. Refer to
SRC-16, "Trouble Diagnosis with CONSULT"
.
JMHIA0009ZZ
ALHIA0385ZZ
FRONT PASSENGER AIR BAG MODULE
SR-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
FRONT PASSENGER AIR BAG MODULE
Exploded View
INFOID:0000000011279758
Removal and Installation
INFOID:0000000011279759
WARNING:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
• Always work from the side of air bag module. Do not work in front of it.
• Do not use air tools or electric tools for servicing.
REMOVAL
1. Remove the Instrument panel assembly. Refer to
IP-14, "INSTRUMENT PANEL ASSEMBLY : Removal
2. Remove front passenger air bag module screws.
3. Release the pawls by removing the front passenger air bag
module as shown.
: Pawl
CAUTION:
AWHIA0732ZZ
1.
Front passenger air bag module 2.
Steering member
ALHIA0386ZZ
SR-18
< REMOVAL AND INSTALLATION >
FRONT PASSENGER AIR BAG MODULE
• Always place the front passenger air bag module with pad
side facing upward as shown.
: Upward
• Replace the front passenger air bag module if it has been
dropped or sustained an impact.
• Do not strike the front passenger air bag module.
• Do not insert any foreign objects (screwdriver, etc.) into the passenger air bag module.
• Do not disassemble the passenger air bag module.
• Do not expose the passenger air bag module to temperatures exceeding 90
°C (194°F).
• Do not allow oil, grease, detergent, or water to come in contact with the front passenger air bag mod-
ule.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Do not reuse the front passenger air bag module bolts.
• Do not damage the front passenger air bag module harness during installation.
• After installation is complete, check that no system malfunction is detected causing the air bag
warning lamp to illuminate.
• If a malfunction is indicated by the air bag warning lamp after repair or replacement of the malfunc-
tioning parts, perform the SRS final check. Refer to
SRC-16, "Trouble Diagnosis with CONSULT"
.
ALHIA0387ZZ
JMHIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст