Nissan Rogue. Manual — part 322
DLK-130
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2422 BACK DOOR STATE
Is the difference between the 2 monitor items 10 or more?
YES
>> GO TO 4.
NO
>> Replace automatic back door control module. Refer to
DLK-283, "Removal and Installation"
.
4.
CHECK ENCODER POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect spindle unit connector.
3. Check voltage between spindle unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
CHECK ENCODER CIRCUIT
1. Disconnect automatic back door control module connector.
2. Check continuity between automatic back door control module harness connector and spindle unit har-
ness connector.
3. Check continuity between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control module. Refer to
DLK-283, "Removal and Installation"
.
NO
>> Repair or replace harness.
6.
CHECK ENCODER CIRCUIT 2
1. Disconnect automatic back door control module connector.
2. Check continuity between automatic back door control module harness connector and spindle unit har-
ness connector.
Monitor item
Status
SPINDLE SENSOR LH
0 – 65535
SPINDLE SENSOR RH
0 – 65535
(+)
(–)
Voltage
(Approx.)
Spindle unit
Connector
Terminal
LH
B95
4
Ground
Battery voltage
RH
B73
Automatic back door control module
Spindle unit
Continuity
Connector
Terminal
Connector
Terminal
B55
19
LH
B95
4
Yes
20
RH
B73
Automatic back door control module
Ground
Continuity
Connector
Terminal
B55
19
No
20
2015 Rogue NAM
B2422 BACK DOOR STATE
DLK-131
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Check continuity between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK ENCODER CIRCUIT 3
1. Connect automatic back door control module and spindle unit connector
2. Check continuity between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Replace automatic back door control module. Refer to
DLK-283, "Removal and Installation"
.
8.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace automatic back door control module. Refer to
DLK-283, "Removal and Installation"
.
NO
>> Repair or replace the malfunctioning parts.
Automatic back door control module
Spindle unit
Continuity
Connector
Terminal
Connector
Terminal
B55
6
LH
B95
3
Yes
7
5
8
RH
B73
3
9
5
Automatic back door control module
Ground
Continuity
Connector
Terminal
B55
6
No
7
8
9
Automatic back door control module
Ground
Voltage
(Approx.)
Connector
Terminal
B55
21
0 V
2015 Rogue NAM
DLK-132
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2423 AUTOMATIC BACK DOOR MOTOR OPERATION TIME
B2423 AUTOMATIC BACK DOOR MOTOR OPERATION TIME
DTC Logic
INFOID:0000000011278842
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Operate automatic back door.
3. Check “Self Diagnostic Result” of “AUTO BACK DOOR” using CONSULT.
Is DTC detected?
YES
>> Refer to
DLK-132, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011278843
Regarding Wiring Diagram information, refer to
.
1.
ERASE DTC
1. At least 180 seconds are passed after automatic back door operation is inhibited.
2. Erase DTC, and then repeat “PERFORM DTC CONFIRMATION PROCEDURE”.
Is DTC detected?
YES
>> GO TO 2.
NO
>> Inspection End.
2.
CHECK SPINDLE MOTOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic back door control module and spindle unit connector.
3. Check continuity between automatic back door control module harness connector and spindle unit har-
ness connector.
4. Check continuity between automatic back door control module harness connector and ground.
DTC
CONSULT display de-
scription
DTC detecting condition
Possible cause
B2423
ABD MTR TIME OUT
When the automatic back door control module and
spindle motor operate in the same direction for 180
seconds or more continuously.
• Spindle motor
• Automatic back door control
module
• Harness or connector
Automatic back door control module
Spindle unit
Continuity
Connector
Terminal
Connector
Terminal
B56
27
LH
B95
1
Yes
34
7
29
RH
B73
1
36
7
2015 Rogue NAM
B2423 AUTOMATIC BACK DOOR MOTOR OPERATION TIME
DLK-133
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Replace automatic back door control module. Refer to
DLK-283, "Removal and Installation"
.
NO
>> Repair or replace harness.
Automatic back door control module
Ground
Continuity
Connector
Terminal
B56
27
No
29
34
36
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст