Nissan Rogue. Manual — part 391
DLN-8
< PREPARATION >
[TRANSFER: TY21C]
PREPARATION
Drift
a: 56.5 mm (2.224 in) dia.
b: 48 mm (1.89 in) dia.
Installing side oil seal (installing transfer case
oil seal)
Drift
a: 44 mm (1.73 in) dia.
b: 33 mm (1.3 in) dia.
Installing ring gear shaft oil seal
Puller
Removing ring gear bearing (left) inner race
(transfer case side)
Drift
a: 70 mm (2.76 in) dia.
b: 60 mm (2.36 in) dia.
Installing oil seal (installing pinion bearing
seal)
Drift
a: 78 mm (3.07 in) dia.
b: 68 mm (2.68 in) dia.
Installing side oil seal (installing transfer cover
oil seal)
Replacer
• Removing drive pinion
• Removing ring gear bearing (left) inner race
(transfer cover side)
Drift
a: 58 mm (2.28 in) dia.
b: 55 mm (2.17 in) dia.
Installing ring gear bearing (left) inner race
(transfer case side)
Tool name
Description
NT115
NT115
NT077
NT115
NT115
ZZA0700D
NT115
PREPARATION
DLN-9
< PREPARATION >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Drift
a: 62 mm (2.44 in) dia.
b: 58 mm (2.28 in) dia.
Installing ring gear bearing (right) inner race
(transfer cover side)
Drift
a: 73.5 mm (2.894 in) dia.
Installing ring gear bearing (left) outer race
(transfer case side)
Drift
a: 87 mm (3.43 in) dia.
Installing ring gear bearing (right) outer race
(transfer cover side)
Drift
a: 20 mm (0.79 in) dia.
Removing drive pinion
Drift
a: 40 mm (1.57 in) dia.
b: 25 mm (0.98 in) dia.
Installing companion flange
Tool name
Description
NT115
SCIA5338E
SCIA5338E
SCIA5338E
NT115
DLN-10
< SYSTEM DESCRIPTION >
[TRANSFER: TY21C]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000011278291
Instrument lower panel LH
Rear final drive assembly
Rear wheel house outer panel in lug-
gage room of left side
ALDIA0553ZZ
No.
Component
Function
Combination meter
Mainly transmits the following signal to AWD control unit via CAN com-
munication:
• Parking brake switch signal
Mainly receives the following signals from AWD control unit via CAN
communication:
• AWD warning lamp signal
• AWD LOCK indicator lamp signal
• Torque distribution indicator signal
For detailed installation location, refer to
.
Steering angle sensor
Mainly transmits the following signal to AWD control unit via CAN com-
munication:
• Steering angle sensor signal
For detailed installation location, refer to
.
COMPONENT PARTS
DLN-11
< SYSTEM DESCRIPTION >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AWD Control Unit
INFOID:0000000011278292
• Controls driving force distribution by signals from each sensor from front wheel driving mode (100:0) to 4-
wheel driving mode (50:50).
• Front wheel driving conditions is available by fail-safe function if malfunction is detected in AWD system.
• AWD actuator relay is integrated with AWD control unit, and supplies AWD solenoid with voltage.
Electric Controlled Coupling
INFOID:0000000011278293
Electric controlled coupling is integrated with rear final drive and transmits driving force to rear final drive. For
operation, refer to
DLN-12, "Operation Description"
.
AWD Solenoid
INFOID:0000000011278294
Controls electric controlled coupling by command current from AWD control unit.
AWD Lock Switch
INFOID:0000000011278295
Every time AWD lock switch is pressed, AUTO mode and LOCK mode switch each other.
ABS actuator and electric unit (control unit)
Mainly transmits the following signals to AWD control unit via CAN
communication:
• Each wheel speed signal
• Stop lamp switch signal (brake signal)
• Yaw rate sensor signal
• Side G sensor signal
• Decel G sensor signal
For detailed installation location, refer to
ECM
Mainly transmits the following signals to AWD control unit via CAN
communication:
• Accelerator pedal position signal
• Engine speed signal
For detailed installation location, refer to
.
AWD lock switch
Refer to
.
Electric controlled coupling
Refer to
DLN-11, "Electric Controlled Coupling"
AWD solenoid
Refer to
AWD control unit
• AWD actuator relay
Refer to
No.
Component
Function
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст