Nissan Qashqai J11. Manual — part 2127
AV
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
AV-197
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK RH SIDE CAMERA POWER SUPPLY VOLTAGE
1.
Connect around view monitor control unit and RH side camera connectors.
2.
Turn ignition switch ON.
3.
Check voltage between around view monitor control unit connector M8 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-267, "Removal and Installation"
3.
CHECK RH SIDE CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit and RH side camera connectors.
3.
Check continuity between around view monitor control unit connector M8 and RH side camera connector
D27.
4.
Check continuity between around view monitor control unit connector M8 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
CHECK RH SIDE CAMERA IMAGE SIGNAL
1.
Connect around view monitor control unit and RH side camera connectors.
2.
Turn ignition switch ON.
3.
Check signal between the terminals of around view monitor control unit connector M8.
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M8
62
No
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M8
62
—
CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
Around view monitor control unit
RH side camera
Continuity
Connector
Terminals
Connector
Terminals
M8
65
D27
16
Yes
66
15
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M8
65
No
AV-198
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
Is the inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
AV-267, "Removal and Installation"
NO
>> Replace RH side camera. Refer to
AV-269, "Removal and Installation"
Around view monitor control unit connector M8
Condition
Reference value
(+)
(
−
)
Terminal
Terminal
65
66
CAMERA switch is ON or se-
lector lever in R (reverse).
JSNIA0834GB
AV
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
AV-199
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000010435694
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000010435695
Regarding Wiring Diagram information, refer to
.
WITHOUT DRIVER ASSISTANCE SYSTEM
1.
CHECK FRONT CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit and front camera connectors.
3.
Check continuity between around view monitor control unit connector M95 and front camera connector
E106.
4.
Check continuity between around view monitor control unit connector M95 and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK FRONT CAMERA POWER SUPPLY VOLTAGE
1.
Connect around view monitor control unit and front camera connectors.
2.
Turn ignition switch ON.
3.
Check voltage between around view monitor control unit connector M95 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-267, "Removal and Installation"
3.
CHECK FRONT CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit and front camera connectors.
CONSULT Display
DTC Detection Condition
Possible Cause
Front display output signal diag-
nosis (Harness disconnection)
[U111C]
Front camera image signal circuit open or short.
Check front camera image signal circuit.
Around view monitor control unit
Front camera
Continuity
Connector
Terminals
Connector
Terminals
M95
38
E106
2
Yes
37
1
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M95
38
No
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M95
38
—
CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
AV-200
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
3.
Check continuity between around view monitor control unit connector M95 and front camera connector
E106.
4.
Check continuity between around view monitor control unit connector M95 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
CHECK FRONT CAMERA IMAGE SIGNAL
1.
Connect around view monitor control unit and front camera connectors.
2.
Turn ignition switch ON.
3.
Check signal between the terminals of around view monitor control unit connector M95.
Is the inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
AV-267, "Removal and Installation"
NO
>> Replace front camera. Refer to
AV-268, "Removal and Installation"
.
WITH DRIVER ASSISTANCE SYSTEM
1.
CHECK FRONT CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit and front camera connectors.
3.
Check continuity between around view monitor control unit connector M8 and front camera connector
E106.
4.
Check continuity between around view monitor control unit connector M8 and ground.
Around view monitor control unit
Front camera
Continuity
Connector
Terminals
Connector
Terminals
M95
40
E106
4
Yes
39
5
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M95
40
No
Around view monitor control unit connector M95
Condition
Reference value
(+)
(
−
)
Terminal
Terminal
40
39
CAMERA switch is ON or se-
lector lever in R (reverse).
JSNIA0834GB
Around view monitor control unit
Front camera
Continuity
Connector
Terminals
Connector
Terminals
M8
68
E106
2
Yes
70
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст