Nissan Qashqai J11. Manual — part 981
SYSTEM SETTINGS CANNOT BE TURNED ON/OFF ON THE INTEGRAL
SWITCH
BRC-161
< SYMPTOM DIAGNOSIS >
[FORWARD EMERGENCY BRAKING]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
SYMPTOM DIAGNOSIS
SYSTEM SETTINGS CANNOT BE TURNED ON/OFF ON THE INTEGRAL
SWITCH
Symptom Table
INFOID:0000000010501249
CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected.
Description
INFOID:0000000010501250
FEB system does not turn on/off.
• FEB warning lamp does not illuminate even if the steering switch is operated when FEB warning lamp is not
illuminated.
• FEB warning lamp does not turn off even if the steering switch is operated when FEB warning lamp is illumi-
nated.
NOTE:
The system ON/OFF condition will be memorized even if the ignition switch turns OFF.
Diagnosis Procedure
INFOID:0000000010501251
1.
PERFORM THE SELF-DIAGNOSIS
1.
Perform “All DTC Reading” with CONSULT.
2.
Check if the DTC is detected in self-diagnosis results for “LASER/RADAR” with CONSULT.
Is any DTC detected?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
STEERING SWITCH INSPECTION
1.
Turn ignition switch ON.
2.
Check that “FEB SELECT” operates normally in “DATA MONITOR” for “LASER/RADAR” with CONSULT.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the distance sensor. Refer to
DAS-203, "Removal and Installation"
.
3.
FEB WARNING LAMP
1.
Select the active test item “” for “LASER/RADAR” with CONSULT.
2.
Check if the FEB warning lamp illuminates when the test item is operated.
Is the inspection result normal?
YES
>> Refer to
.
NO
>> GO TO 4.
4.
CHECK DATA MONITOR OF COMBINATION METER
Check that “BA W/L” operates normally in “” for “METER/M&A” with CONSULT, when the FEB setting ON by
steering switch.
Is the inspection result normal?
YES
>> Replace the combination meter.
MWI-80, "Removal and Installation"
NO
>> Replace the distance sensor. Refer to
DAS-203, "Removal and Installation"
.
5.
REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts.
Symptom
Inspection item/Reference page
FEB system does not turn ON/OFF
FEB warning lamp is not turned ON
⇔
OFF
when operating steering switch
BRC-162
< SYMPTOM DIAGNOSIS >
[FORWARD EMERGENCY BRAKING]
SYSTEM SETTINGS CANNOT BE TURNED ON/OFF ON THE INTEGRAL
SWITCH
>> GO TO 6.
6.
CHECK FEB SYSTEM
Check that FEB warning lamp turned ON
⇔
OFF, when operating steering switch.
>> INSPECTION END
ST-1
STEERING
C
D
E
F
H
I
J
K
L
M
SECTION
ST
A
B
ST
N
O
P
CONTENTS
STEERING SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Removing Battery Terminal . . .....
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect . . . . . . . . .....
Service Notice or Precautions for Steering System
. ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
BASIC INSPECTION . . . . . . . . .
STEERING WHEEL . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
STEERING WHEEL . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
STEERING COLUMN . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
STEERING GEAR AND LINKAGE . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
ST-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precautions for Removing Battery Terminal
INFOID:0000000010508843
• With the adoption of Auto ACC function, ACC power is automatically supplied by operating the intelligent key
or remote keyless entry or by opening/closing the driver side door. In addition, ACC power is supplied even
after the ignition switch is turned to the OFF position, i.e. ACC power is supplied for a certain fixed time.
• When disconnecting the 12V battery terminal, turn off the ACC
power before disconnecting the 12V battery terminal, observing
“How to disconnect 12V battery terminal” described below.
NOTE:
Some ECUs operate for a certain fixed time even after ignition
switch is turned OFF and ignition power supply is stopped. If the
battery terminal is disconnected before ECU stops, accidental DTC
detection or ECU data damage may occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
HOW TO DISCONNECT 12V BATTERY TERMINAL
Disconnect 12V battery terminal according to Instruction 1 or Instruction 2 described below.
For vehicles parked by ignition switch OFF, refer to Instruction 2.
INSTRUCTION 1
1.
Open the hood.
2.
Turn key switch to the OFF position with the driver side door opened.
3.
Get out of the vehicle and close the driver side door.
4.
Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse
of the specified time.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
5.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
INSTRUCTION 2 (FOR VEHICLES PARKED BY IGNITION SWITCH OFF)
1.
Unlock the door with intelligent key or remote keyless entry.
NOTE:
At this moment, ACC power is supplied.
2.
Open the driver side door.
3.
Open the hood.
4.
Close the driver side door.
5.
Wait at least 3 minutes.
SEF289H
D4D engine
: 20 minutes
HRA2DDT
: 12 minutes
K9K engine
: 4 minutes
M9R engine
: 4 minutes
R9M engine
: 4 minutes
V9X engine
: 4 minutes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст