Nissan Qashqai J11. Manual — part 1512
PWC-28
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000010286486
DETAILED FLOW
1.
OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicle in.
>> GO TO 2.
2.
REPRODUCE THE MALFUNCTION INFORMATION
Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
>> GO TO 3.
3.
IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”
Use “Symptom diagnosis” from the symptom inspection result in step 2 and then identify where to start per-
forming the diagnosis based on possible causes and symptoms.
>> GO TO 4.
4.
IDENTIFY THE MALFUNCTIONING PARTS WITH “COMPONENT DIAGNOSIS”
Perform the diagnosis with “Component diagnosis” of the applicable system.
>> GO TO 5.
5.
REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 6.
6.
FINAL CHECK
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 2.
Are the malfunctions corrected?
YES
>> INSPECTION END
NO
>> GO TO 3.
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
PWC-29
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMI-
NAL
Description
INFOID:0000000010286487
When the battery negative terminal is disconnected, the initialization is necessary for normal operation of
power window system. Refer to
.
CAUTION:
The following specified operations cannot be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000010286488
1.
SYSTEM INITIALIZATION
Perform system initialization. Refer to
.
>> GO TO 2.
2.
CHECK ANTI-PINCH FUNCTION
Check anti-pinch function. Refer to
.
>> END
PWC-30
< BASIC INSPECTION >
ADDITIONAL SERVICE WHEN REPLACING POWER WINDOW MAIN SWITCH
ADDITIONAL SERVICE WHEN REPLACING POWER WINDOW MAIN
SWITCH
Description
INFOID:0000000010286489
When the control unit replaced, the initialization in necessary for normal operation of power window system.
Refer to
CAUTION:
The following specified operations cannot be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000010286490
1.
SYSTEM INITIALIZATION
Perform system initialization. Refer to
.
>> GO TO 2.
2.
CHECK ANTI-PINCH FUNCTION
Check anti-pinch function. Refer to
.
>> END
SYSTEM INITIALIZATION
PWC-31
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
SYSTEM INITIALIZATION
Description
INFOID:0000000010286491
If any of the following operations are performed, the initialization is necessary for normal operation of power
window system. Refer to
• Disconnection and connection of battery cable from negative terminal.
• When power window main switch replaced.
• Electric power supply to power window main switch or power window motor (driver side) is interrupted by
blown fuse or disconnection and connection of the negative terminal of battery, etc.
• Disconnection and connection of power window main switch harness connector.
• Removal of power window motor (driver side) from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of glass.
• Removal and installation of door glass run.
CAUTION:
The following specified operations cannot be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000010286492
1.
STEP 1
1.
Turn ignition switch ON.
2.
Operate power window main switch to fully open the front door glass (driver side).
-
This operation is unnecessary if the front door glass (driver side) is already fully open.
3.
Continue pulling the power window main switch UP (AUTO-UP operation). Even after front door glass
(driver side) stops at fully closed position, keep pulling the switch for 2 seconds or more.
4.
Check that AUTO-UP function operates normally.
>> GO TO 2.
2.
STEP 2
Check anti-pinch function. Refer to
.
>> END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст