Nissan Qashqai J11. Manual — part 702
CVT SHIFT SELECTOR
TM-383
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
a.
Slide the selector lever knob cover
down.
CAUTION:
Never damage the knob cover.
b.
Pull out the lock pin
from the selector lever knob
.
c.
Pull the selector lever knob and the selector lever knob cover
upwards to remove them.
6.
Remove the center console. Refer to
.
7.
Shift the selector lever to “P” position.
8.
Disconnect the tip
of control cable and remove socket
from
the CVT shift selector assembly.
9.
Disconnect the CVT shift selector connector
.
10. Remove the CVT shift selector assembly from the vehicle.
INSTALLATION
Note the followings and install in the reverse order of removal.
• Pay attention to the following when connecting the control cable to the CVT shift selector assembly.
1.
When connecting the control cable
to the CVT shift selector
assembly
, face the grooved surface of the rib
up and insert
the control cable until it stops.
NOTE:
Apply multi-purpose grease to control cable eye before installa-
tion.
JSDIA2778ZZ
JSDIA4220ZZ
JSDIA5384ZZ
JSDIA1624ZZ
TM-384
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
CVT SHIFT SELECTOR
2.
Install the socket
onto the CVT shift selector assembly.
CAUTION:
• Place the socket onto the CVT shift selector assembly,
then fasten it in place from above.
• Check that the pulling on the socket does not disconnect
it.
• Follow the procedure below and place the selector lever knob onto the CVT shift selector.
1.
Install the lock pin
onto the selector lever knob
.
2.
Install the knob cover
onto the selector lever knob.
3.
Shift the selector lever to “N” position.
4.
Press the selector lever knob onto the selector lever until it
clicks.
CAUTION:
• When install, never press selector button.
• Never strike the selector lever knob to press it into place.
5.
After installing selector lever knob, pull the knob to check that it
does not become disconnected.
Disassembly and Assembly
INFOID:0000000010668188
DISASSEMBLY
1.
Remove the position lamp.
2.
Disengage the hooks (4 locations), and lift up the position indication panel to separate it from the CVT shift
selector assembly.
CAUTION:
Never damage the CVT shift selector assembly.
3.
Remove shift lock unit mounting screws.
4.
Remove the shift lock unit from the CVT shift selector assembly.
5.
Disconnect the park position switch connector, detent switch connector and shift lock solenoid connector
from the shift lock unit.
ASSEMBLY
Assemble in the reverse order of disassembly.
Inspection
INFOID:0000000010668189
INSPECTION AFTER INSTALLATION
• Check the CVT shift selector position. Refer to
• Check that shift lock can be forcible release. Refer to
TM-234, "SHIFT LOCK SYSTEM : System Descrip-
• The key can be removed only when the selector lever is in the “P” position. (Without push engine starter)
• It must not be possible to turn the ignition switch to LOCK when the selector lever is not in the “P” position.
(Without push engine starter)
JSDIA1810ZZ
JSDIA2778ZZ
CONTROL CABLE
TM-385
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL CABLE
Exploded View
INFOID:0000000010668190
Removal and Installation
INFOID:0000000010668191
CAUTION:
Always apply the parking brake before performing removal and installation.
REMOVAL
1.
Apply the parking brake.
CAUTION:
Make sure the vehicle cannot move with the parking brake applied.
2.
Remove the center console. Refer to
IP-19, "Removal and Installation"
.
3.
Remove the position lamp.
Control cable
Lock plate
Transaxle assembly
Manual lever
Bracket
Bracket
Grommet
CVT shift selector assembly
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSDIA5630GB
TM-386
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
CONTROL CABLE
4.
Disengage the hooks
(4 locations), and lift up the position
indication panel
to separate it from the CVT shift selector.
CAUTION:
Never damage the CVT shift selector assembly.
5.
Disconnect the tip
of control cable and remove socket
from
the CVT shift selector assembly.
6.
Disengage the pawls (
) of the grommet
and pull down-
wards to remove.
7.
Remove the battery mounting bracket assembly. Refer to
8.
Remove the harness bracket from battery mounting bracket.
9.
Remove the control cable nut (
) and remove the control cable
from the manual lever
.
10. Remove the lock plate
and remove the control cable
from
bracket .
11. Remove the exhaust front tube. Refer to
12. Remove heat plate.
JSDIA4229ZZ
JSDIA4220ZZ
JSDIA5182ZZ
: Vehicle front
JSDIA6039ZZ
: Vehicle front
JSDIA5184ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст