Nissan Qashqai J11. Manual — part 995
STC-40
< SYMPTOM DIAGNOSIS >
POWER STEERING WARNING LAMP DOSE NOT TURN OFF
POWER STEERING WARNING LAMP DOSE NOT TURN OFF
Description
INFOID:0000000010452136
Power steering warning lamp does not turn OFF several seconds after engine started.
Diagnosis Procedure
INFOID:0000000010452137
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Turn the ignition switch OFF to ON.
2.
Perform “EPS/DAST 3” self-diagnosis.
Is any DTC detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 2.
2.
CHECK POWER STEERING WARNING LAMP
Perform the trouble diagnosis of power steering warning lamp. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the specific malfunctioning part.
3.
CHECK EPS CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis of EPS control unit power supply and ground. Refer to
Is the inspection result normal?
YES
>> Check that there is no malfunction in each harness connector pin terminal or disconnection.
NO
>> Repair or replace the specific malfunctioning part.
STEERING WHEEL TURNING FORCE IS HEAVY OR LIGHT
STC-41
< SYMPTOM DIAGNOSIS >
C
D
E
F
H
I
J
K
L
M
A
B
STC
N
O
P
STEERING WHEEL TURNING FORCE IS HEAVY OR LIGHT
Description
INFOID:0000000010452138
Steering wheel turning force is heavy or light.
Diagnosis Procedure
INFOID:0000000010452139
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Turn the ignition switch OFF to ON.
2.
Perform “EPS/DAST 3” self-diagnosis.
Is any DTC detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 2.
2.
CHECK THE ILLUMINATION OF THE POWER STEERING WARNING LAMP
Check that the power steering warning lamp turns ON when ignition switch turns ON. Then, power steering
warning lamp turns OFF after the engine is started.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Perform trouble diagnosis of power steering warning lamp. Refer to
.
3.
CHECK EPS CONTROL UNIT SIGNAL (1)
With CONSULT
1.
Start the engine.
CAUTION:
Never drive the vehicle.
2.
Select “ASSIST LEVEL” in “DATA MONITOR” in “EPS/DAST 3”.
Dose the item in “DATA MONITOR” indicate “100%”?
YES
>> GO TO 6.
NO
>> GO TO 4.
4.
CHECK EPS CONTROL UNIT SIGNAL (2)
With CONSULT
Select “BATTERY VOLT” in “DATA MONITOR” in “EPS/DAST 3”.
Dose the item in “DATA MONITOR” indicate “10.5 V” or more?
YES
>> GO TO 5.
NO
>> Perform trouble diagnosis of EPS control unit power supply and ground. Refer to
.
5.
CHECK EPS CONTROL UNIT SIGNAL (3)
With CONSULT
1.
Select “ASSIST LEVEL” in “DATA MONITOR” in “EPS/DAST 3”.
2.
Stop the EPS system until the item in “DATA MONITOR” becomes “100%”.
NOTE:
While stopping the EPS system, do not turn steering wheel.
3.
Check that the symptom continues.
Dose the symptom continue?
YES
>> GO TO 6.
NO
>> The assist torque decreases because of protection function. This is not malfunction. INSPEC-
TION END
6.
CHECK EPS CONTROL UNIT SIGNAL (4)
With CONSULT
1.
Start the engine.
STC-42
< SYMPTOM DIAGNOSIS >
STEERING WHEEL TURNING FORCE IS HEAVY OR LIGHT
CAUTION:
Never drive the vehicle.
2.
Turn steering wheel from full left stop to full right stop.
3.
Select “TORQUE SENSOR” in “DATA MONITOR” in “EPS/DAST 3”.
Is the inspection result normal?
YES-1 (Models without Stop/Start System)>>GO TO 9.
YES-2 (Models with Stop/Start System)>>GO TO 8.
NO
>> GO TO 7.
7.
CHECK EPS MOTOR
Perform the trouble diagnosis of EPS motor. Refer to
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace the specific malfunctioning part.
8.
CHECK STOP/START SYSTEM
With CONSULT
1.
Start the engine.
CAUTION:
Never drive the vehicle.
2.
Select “ST TORQUE STATUS” and “STOP/START SYSTEM” in “DATA MONITOR” in “EPS/DAST 3”.
3.
Operate stop/start system. Refer to
ECH-35, "STOP/START SYSTEM : System Description"
ECK-39, "STOP/START SYSTEM : System Description"
(K9K),
EC9-42, "STOP/START SYSTEM : Sys-
EC9-50, "STOP/START SYSTEM : System Description (CVT
(R9M).
4.
Turn the steering wheel.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Check the ECM. Refer to
(K9K),
9.
CHECK STEERING WHEEL TURNING FORCE
Check the steering wheel turning force. Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check the steering wheel turning force for mechanical malfunction. Refer to
Monitor item
Condition
Display value
TORQUE SENSOR
Steering wheel: Not steer-
ing (There is no steering
force)
Approx. 0.0 Nm
Steering wheel: Right turn
Positive value (Nm)
Steering wheel: Left turn
Negative value (Nm)
Monitor item
Condition
Display value
ST TORQUE STA-
TUS
Steering wheel: Not steering (There is
no steering force)
Off
STOP/START SYS-
TEM
When stop/start system is active
On
Monitor item
Condition
Display value
ST TORQUE STA-
TUS
Steering wheel: Right or left turn
On
STOP/START SYS-
TEM
When stop/start system is prohibited
Off
UNBALANCE STEERING WHEEL TURNING FORCE AND RETURN BETWEEN
RIGHT AND LEFT
STC-43
< SYMPTOM DIAGNOSIS >
C
D
E
F
H
I
J
K
L
M
A
B
STC
N
O
P
UNBALANCE STEERING WHEEL TURNING FORCE AND RETURN BE-
TWEEN RIGHT AND LEFT
Description
INFOID:0000000010452140
Unbalance steering wheel turning force and return between right and left.
Diagnosis Procedure
INFOID:0000000010452141
1.
CHECK THE ILLUMINATION OF THE POWER STEERING WARNING LAMP
Check the power steering warning lamp while engine is running.
Does the power steering warning lamp turn OFF?
YES
>> GO TO 2.
NO
>> Refer to
.
2.
CHECK WHEEL ALIGNMENT
Check the wheel alignment. Refer to
FSU-7, "Wheel Alignment Inspection"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Adjustment of wheel alignment. Refer to
FSU-7, "Wheel Alignment Inspection"
3.
CHECK EPS CONTROL UNIT SIGNAL
With CONSULT
1.
Start the engine.
CAUTION:
Never drive the vehicle.
2.
Turn steering wheel from full left stop to full right stop.
3.
Select “DATA MONITOR” of “EPS/DAST 3” and select “TORQUE SENSOR”.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK EPS MOTOR
Perform the trouble diagnosis of EPS motor. Refer to
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the specific malfunctioning part.
5.
CHECK STEERING WHEEL TURNING FORCE
Check the steering wheel turning force. Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check the steering wheel turning force for mechanical malfunction. Refer to
.
Monitor item
Condition
Display value
TORQUE SENSOR
Steering wheel: Not steer-
ing (There is no steering
force)
Approx. 0.0 Nm
Steering wheel: Right turn
Positive value (Nm)
Steering wheel: Left turn
Negative value (Nm)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст