Nissan Qashqai J11. Manual — part 1228
HOOD LOCK
DLK-181
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• After installation, perform hood fitting adjustment. Refer to
DLK-152, "HOOD ASSEMBLY : Adjust-
• After installation, perform hood lock control inspection. Refer to
.
HOOD SAFETY HOOK
HOOD SAFETY HOOK : Removal and Installation
INFOID:0000000010478165
REMOVAL
Remove mounting nuts, and then remove hood lock secondary assembly.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, perform hood lock control inspection. Refer to
.
Inspection
INFOID:0000000010434723
NOTE:
If the hood lock cable is bent or deformed, replace it.
1.
Check that hood opener operating is condition 49 N (5.0 kg, 11.0 lb) or below.
2.
Check that secondary latch is securely engaged with secondary striker from the dead load of the hood
assembly.
3.
Check that primary latch is securely engaged with primary striker when hood assembly is closed [free-fall
from approximately 200 mm (7.874 in) height].
CAUTION:
Never free-fall hood assembly from a height of 300 (11.811 in) mm or more.
4.
While operating hood opener, carefully check that the front end of hood is raised by approximately 20.0
mm (0.787 in). Also check that hood opener returns to the original position.
5.
Check that secondary latch is properly engaged with secondary striker [4.0 mm (0.157 in)].
6.
Check the hood lock lubrication condition. If necessary, apply
body grease to hood lock assembly.
: Body grease
JMKIB1164ZZ
DLK-182
< REMOVAL AND INSTALLATION >
[TYPE 1]
FRONT DOOR LOCK
FRONT DOOR LOCK
Exploded View
INFOID:0000000010434724
*
1
: Driver side only
1.
Outside handle escutcheon
2.
Outside handle grip
3.
Front gasket
4.
Inside handle
5.
cable clip
6.
Door lock assembly
7.
Key rod protector*
1
8.
Key rod*
1
9.
TORX bolt
10. Outside handle bracket
11. Rear gasket
: Pawl
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
JMKIB3252GB
FRONT DOOR LOCK
DLK-183
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010434725
REMOVAL
1.
Disconnect inside handle cable from inside handle. Refer to
DLK-183, "INSIDE HANDLE : Removal and
.
2.
Disconnect outside handle cable from outside handle bracket. Refer to
.
3.
Disconnect door lock assembly harness connector.
4.
Remove door lock assembly screws, and then remove door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse door lock assembly screw. Always replace it with a new one when it is removed.
• Check door lock cable is properly engaged with outside handle bracket.
• When installing key rod, rotate key rod holder until a click is felt.
• Check door lock assembly for poor lubrication. Refer to
DLK-183, "DOOR LOCK : Inspection"
• Check door open/close, lock/unlock operation after installation.
DOOR LOCK : Inspection
INFOID:0000000010434726
Check door lock assembly for poor lubrication. Apply body grease if
necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000010434727
REMOVAL
1.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Remove inside handle mounting bolt.
3.
Disengage inside handle from door panel while sliding inside handle toward vehicle rear, and then sepa-
rate inside handle.
4.
Disconnect inside handle cable, and then remove inside handle.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010434728
REMOVAL
1.
Fully close the front door glass.
2.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
3.
Remove sealing screen.
: Body grease
JMKIA8534ZZ
DLK-184
< REMOVAL AND INSTALLATION >
[TYPE 1]
FRONT DOOR LOCK
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
4.
Remove front door glass rear run. Refer to
GW-23, "Removal and Installation"
.
5.
Remove key rod protector mounting bolts, and then remove key rod protector.
6.
Disengage outside handle cable from cable clip.
7.
Disengage rod holder, and then disconnect key rod from door lock assembly. (Driver side only)
8.
Disconnect outside handle harness connector.
9.
Remove grommet (1) of door side. Loosen, through grommet hole, TORX bolt (2) that fixes outside handle
escutcheon.
10. While pulling outside handle (1)according to the numerical order
1
→
2 indicated by arrows as shown in the figure, remove outside
handle escutcheon (2).
11. While pulling outside handle (1) according to the numerical order
1
→
2 indicated by arrows as shown in the figure, slide toward
rear of vehicle to remove outside handle.
12. Remove front gasket (1) and rear gasket (2).
JMKIB0585ZZ
JMKIA0441ZZ
JMKIA2948ZZ
JMKIB2240ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст