Nissan Qashqai J11. Manual — part 1594
BRM-204
< REMOVAL AND INSTALLATION >
[FOR EUROPE (RHD)]
REPLACEMENT OPERATIONS
: Vehicle front
: Welding method and the number of welding points apply to both side of the vehicle.
Replacement part
z
Front roof rail assembly
z
Rear roof rail assembly
JSKIA4033ZZ
BODY ALIGNMENT
BRM-205
< SERVICE DATA AND SPECIFICATIONS (SDS)
[FOR EUROPE (RHD)]
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
BODY ALIGNMENT
2WD
2WD : Body Center Marks (Without Sunroof Models)
INFOID:0000000010498836
A mark is placed on each part of the body to indicate the vehicle center. When repairing the vehicle frame
(members, pillars, etc.) damaged by an accident which it enables more accurate and effective repair by using
these marks together with body alignment specifications.
Unit: mm (in)
: Vehicle front
Points
Portion
Marks
A
Front roof
Embossment
B
Cowl top
indent
C
Cowl top
Hole
φ
8 (0.31)
JSKIA3956ZZ
BRM-206
< SERVICE DATA AND SPECIFICATIONS (SDS)
[FOR EUROPE (RHD)]
BODY ALIGNMENT
2WD : Body Center Marks (With Sunroof Models)
INFOID:0000000010498837
A mark is placed on each part of the body to indicate the vehicle center. When repairing the vehicle frame
(members, pillars, etc.) damaged by an accident which it enables more accurate and effective repair by using
these marks together with body alignment specifications.
Unit: mm (in)
D
Trans control reinforcement
Hole 12
×
14 (0.47
×
0.55)
E
Rear roof
Embossment
Points
Portion
Marks
: Vehicle front
Points
Portion
Marks
A
Upper front roof rail
Embossment
B
Cowl top
indent
C
Cowl top
Hole
φ
8 (0.31)
JSKIA3957ZZ
BODY ALIGNMENT
BRM-207
< SERVICE DATA AND SPECIFICATIONS (SDS)
[FOR EUROPE (RHD)]
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
2WD : Description
INFOID:0000000010498838
• All dimensions indicated in the figures are actual.
• When using a tracking gauge, adjust both pointers to equal length. Then check the pointers and gauge itself
to make sure there is no free play.
• When a measuring tape is used, check to be sure there is no elongation, twisting or bending.
• Measurements should be taken at the center of the mounting holes.
• An asterisk (*) following the value at the measuring point indicates that the measuring point on the other side
is symmetrically the same value.
• The coordinates of the measurement points are the distances measured from the standard line of
″
X
″
,
″
Y
″
and
″
Z
″
.
•
″
Z
″
: Imaginary base line [200 mm (7.87 in) below datum line (
″
0Z
″
at design plan)]
2WD : Engine Compartment (R9M Engine Models)
INFOID:0000000010498839
MEASUREMENT
Dimensions marked with
″
*
″
indicate symmetrically identical dimensions on both the right and left hand of the
vehicle.
D
Trans control reinforcement
Hole 12
×
14 (0.47
×
0.55)
E
Rear roof
Embossment
Points
Portion
Marks
Vehicle center
Front axle center
Imaginary base line
JSKIA0073GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст