Nissan Qashqai J11. Manual — part 2276
BODY MAINTENANCE
MA-139
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
BODY MAINTENANCE
LOCKS, HINGES AND HOOD LATCH
LOCKS, HINGES AND HOOD LATCH : Lubricating
INFOID:0000000010355652
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS : Inspection
INFOID:0000000010355653
For front seat belt illustration. Refer to
.
For rear seat belt illustration. Refer to
CAUTION:
• After any collision, inspect all seat belt assemblies, including retractors and other attached hard-
wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in use
during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improperly
operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal colli-
sion where the driver and passenger air bags are deployed.
• If any component of seat belt assembly is questionable, do not repair.
Replace as seat belt assembly.
• If webbing is cut, frayed, or damaged, replace belt assembly.
• Never oil tongue and buckle.
• Use a genuine NISSAN seat belt assembly.
For details, refer to
• Check anchors for loose mounting
• Check belts for damage
• Check retractor for smooth operation
• Check function of buckles and tongues when buckled and released
BODY CORROSION
BODY CORROSION : Checking Body Corrosion
INFOID:0000000010355654
Visually check body panels for collision damage (scratches, chipping, rubbing, etc.) or damage to the anti-cor-
rosion materials. In particular, check the following locations.
HEMMED PANELS
Hood front end, door lower end, trunk lid rear end, etc.
PANEL JOINT
PART
TYPE 1
TYPE 2
TYPE 3
TYPE 4
HOOD
HOOD LOCK
FRONT DOOR
FRONT DOOR LOCK
REAR DOOR
REAR DOOR LOCK
BACK DOOR
BACK DOOR LOCK
MA-140
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
• Check transaxle surrounding area (oil seal and plug etc.)for fluid
leakage.
• If anything is found, repair or replace damaged parts and adjust
CVT fluid level. Refer to
MA-141, "CVT FLUID (RE0F10D) :
.
CVT FLUID (RE0F10D) : Replacement
INFOID:0000000011497349
CAUTION:
• Always use shop paper. Never use shop cloth.
• Replace a drain plug gasket with new ones at the final stage of the operation when installing.
• Use caution when looking into the drain hole as there is a risk of dripping fluid entering the eye.
• After replacement, always perform CVT fluid leakage check.
1.
Select “Data Monitor” in “TRANSMISSION” using CONSULT.
2.
Select “FLUID TEMP” and confirm that the CVT fluid temperature is 40
°
C (104
°
F) or less.
3.
Check that the selector lever is in the “P” position, then completely engage the parking brake.
4.
Lift up the vehicle.
5.
Remove the drain plug and drain the CVT fluid from the oil pan. Refer to
6.
Install the drain plug to oil pan.
CAUTION:
Drain plug gasket use the old one.
7.
Remove the overflow plug
from converter housing.
8.
Install the charging pipe set (KV311039S0) (A) into the overflow
plug hole.
CAUTION:
Tighten the charging pipe by hand.
9.
Install the ATF changer hose (B) to the charging pipe.
CAUTION:
Press the ATF changer hose all the way onto the charging
pipe until it stops.
10. Fill approximately 3 liter (2-5/8 lmp qt) of the CVT fluid.
11. Remove the ATF changer hose and charging pipe, then install
the overflow plug.
NOTE:
Perform this work quickly because CVT fluid leaks.
12. Lift down the vehicle.
13. Start the engine.
SMA146B
Recommended fluid and fluid capacity
: Refer to
MA-64, "Fluids and Lubricants"
: Vehicle front
JSDIA3714ZZ
JSDIA3713ZZ
SERVICE DATA AND SPECIFICATIONS (SDS)
MA-141
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
DRIVE BELT (HRA2DDT)
DRIVE BELT (HRA2DDT) : Drive Belts
INFOID:0000000010503187
DRIVE BELT (MR20DD)
DRIVE BELT (MR20DD) : Drive Belt
INFOID:0000000010735713
DRIVE BELT
DRIVE BELT (K9K)
DRIVE BELT (K9K) : Drive Belt
INFOID:0000000010503189
DRIVE BELT
DRIVE BELT (R9M)
DRIVE BELT (R9M) : Drive Belts
INFOID:0000000010503190
DRIVE BELT
ENGINE COOLANT (HRA2DDT)
ENGINE COOLANT (HRA2DDT) : Periodical Maintenance Specification
INFOID:0000000010503191
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(Imp qt)
ENGINE COOLANT (MR20DD)
ENGINE COOLANT (MR20DD) : Periodical Maintenance Specification
INFOID:0000000010735716
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(Imp qt)
ENGINE COOLANT (K9K)
Tension of drive belt
Auto adjustment by auto-tensioner
Tension of drive belt
Belt tension is not necessary, as it is automatically adjusted by drive belt auto-tensioner.
Tension of drive belt
Auto adjustment by auto-tensioner
Tension of drive belt
Belt tensioning is not necessary, as it is automatically adjusted by drive belt auto-tensioner.
Engine coolant capacity (With reservoir tank at “MAX” level)
6.5 (5-3/4)
Reservoir tank engine coolant capacity (At “MAX” level)
0.8 (3/4)
Engine coolant capacity (With reservoir tank at “MAX” level)
CVT models
7.4 (6-1/2)
M/T models
7.1 (6-1/4)
Reservoir tank engine coolant capacity (At “MAX” level)
0.8 (3/4)
MA-142
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
ENGINE COOLANT (K9K) : Periodical Maintenance Specification
INFOID:0000000010503192
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(Imp qt)
ENGINE COOLANT (R9M)
ENGINE COOLANT (R9M) : Periodical Maintenance Specification
INFOID:0000000010503193
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(Imp qt)
ENGINE OIL (HRA2DDT)
ENGINE OIL (HRA2DDT) : Periodical Maintenance Specification
INFOID:0000000010503194
ENGINE OIL CAPACITY (APPROXIMATE)
Unit:
(lmp qt)
ENGINE OIL (MR20DD)
ENGINE OIL (MR20DD) : Periodical Maintenance Specification
INFOID:0000000010735717
ENGINE OIL CAPACITY (APPROXIMATE)
Unit:
(lmp qt)
ENGINE OIL (K9K)
ENGINE OIL (K9K) : Periodical Maintenance Specification
INFOID:0000000010503195
ENGINE OIL CAPACITY (APPROXIMATE)
Unit: ·(Imp
qt)
ENGINE OIL (R9M)
ENGINE OIL (R9M) : Periodical Maintenance Specification
INFOID:0000000010503196
ENGINE OIL CAPACITY (APPROXIMATE)
Engine coolant capacity (With reservoir tank at “MAX” level)
6.3 (5-1/2)
Reservoir tank engine coolant capacity (At “MAX” level)
0.8 (3/4)
Engine coolant capacity (With reservoir tank at “MAX” level)
M/T models
7.3 (6-3/8)
CVT models
7.9 (7)
Reservoir tank engine coolant capacity (At “MAX” level)
0.8 (3/4)
Drain and refill
With oil filter change
4.6 (4)
Without oil filter change
4.3 (3-3/4)
Dry engine (Overhaul)
5.6 (4-7/8)
Drain and refill
With oil filter change
3.8 (3-3/8)
Without oil filter change
3.6 (3-1/8)
Dry engine (Overhaul)
4.4 (3-7/8)
With oil filter change
4.55 (4)
Without oil filter change
4.39 (3-7/8)
Dry engine (overhaul)
4.71 (4-1/8)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст