Nissan Qashqai J11. Manual — part 2194
DAS-190
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
POWER SUPPLY AND GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit connector.
3.
Check voltage between around view monitor control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between around view monitor control unit connector and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connectors.
DISTANCE SENSOR
DISTANCE SENSOR : Diagnosis Procedure
INFOID:0000000010416928
1.
CHECK FUSE
Check that the following fuse is not blown.
With stop/start system
Without stop/start system
Is the fuse blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect distance sensor connector.
3.
Check voltage between distance sensor connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between distance sensor connector and ground.
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M95
2
—
Ignition switch: OFF
Battery voltage
4
Ignition switch: ON
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M95
1
—
Existed
Signal name
Fuse No.
Ignition power supply
73 (10A)
Signal name
Fuse No.
Ignition power supply
4 (10A)
Distance sensor
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
E15
1
—
Ignition switch: ON
Battery voltage
DAS
POWER SUPPLY AND GROUND CIRCUIT
DAS-191
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connectors.
FRONT CAMERA UNIT
FRONT CAMERA UNIT : Diagnosis Procedure
INFOID:0000000010663995
WITH PUMP CONTROL UNIT
1.
CHECK FUSE
Check that the following fuses are not blown.
Are the fuses blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit connector.
3.
Check voltage between around view monitor control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between around view monitor control unit connector and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connectors.
WITHOUT PUMP CONTROL UNIT
1.
CHECK FUSE
Check that the following fuses are not blown.
Distance sensor
Ground
Continuity
Connector
Terminal
E15
8
—
Existed
Signal name
Fuse No.
Battery power supply
80 (20A)
Ignition power supply
73 (10A)
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M7
2
—
Ignition switch: OFF
Battery voltage
3
Ignition switch: ON
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M7
1
—
Existed
DAS-192
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
POWER SUPPLY AND GROUND CIRCUIT
Are the fuses blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit connector.
3.
Check voltage between around view monitor control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between around view monitor control unit connector and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connectors.
Signal name
Fuse No.
Battery power supply
80 (20A)
Ignition power supply
73 (10A)
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M95
2
—
Ignition switch: OFF
Battery voltage
4
Ignition switch: ON
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M95
1
—
Existed
DAS
WARNING BUZZER CIRCUIT
DAS-193
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
WARNING BUZZER CIRCUIT
Component Function Check
INFOID:0000000010416933
1.
CHECK WARNING BUZZER
1.
Turn the ignition switch ON.
2.
Select the “Active Test” item “BUZZER” of “BCM” with CONSULT.
3.
While operating the test item, check the operation.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Refer to
DAS-193, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010416934
1.
CHECK WARNING BUZZER OPERATION
While activating the buzzer with CONSULT, listen for the buzzer sound.
Does warning buzzer sound?
YES
>> Replace the around view monitor control unit. Refer to
AV-267, "Removal and Installation"
NO
>> Replace the combination meter (buzzer).
On
: Warning buzzer is activated.
Off
: Warning buzzer is not activated.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст