Nissan Qashqai J11. Manual — part 1701
B20D4 TAIL LAMP LH POWER SUPPLY CIRCUIT
EXL-105
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
With CONSULT
1.
Turn ignition switch OFF.
2.
Turn ignition switch ON.
3.
Turn lighting switch 1ST.
4.
Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
5.
Check DTC.
Is DTC detected?
YES
>> Refer to
EXL-105, "Diagnosis Procedure"
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010452554
1.
CHECK TAIL LAMP LH POWER SUPPLY CIRCUIT (SHORT)
1.
Turn ignition switch OFF.
2.
Turn lighting switch OFF.
3.
Disconnect the following connectors.
-
IPDM E/R
-
Stop lamp / tail lamp LH (body side)
-
Tail lamp LH (back door side)
-
License plate lamp LH
-
License plate lamp RH
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK TAIL LAMP LH POWER SUPPLY
With CONSULT
1.
Connect IPDM E/R connector.
2.
Turn ignition switch ON
3.
Select “TAIL LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.
4.
With operating the test items, check the voltage between stop lamp / tail lamp (body side) harness con-
nector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace IPDM E/R. Refer to
PCS-67, "Removal and Installation"
.
3.
CHECK TAIL LAMP LH
Check the tail lamp LH. Refer to
EXL-106, "Component Inspection (Tail Lamp)"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning part.
4.
CHECK LICENSE PLATE LAMP
IPDM E/R
—
Continuity
Connector
Terminal
E37
4
Ground
Not existed
+
-
Test item
Voltage
Stop lamp / tail lamp (body side)
Connector
Terminal
B22
3
Ground
TAIL LAMP
On
9 – 16 V
Off
0 – 1 V
EXL-106
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
B20D4 TAIL LAMP LH POWER SUPPLY CIRCUIT
Check the license plate lamp. Refer to
EXL-106, "Component Inspection (License Plate Lamp)"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace the malfunctioning part.
Component Inspection (Tail Lamp)
INFOID:0000000010452555
1.
CHECK TAIL LAMP LH
1.
Turn ignition switch OFF.
2.
Disconnect stop lamp / tail lamp LH (body side) and tail lamp LH (back door side) connector.
3.
Check resistance of stop lamp / tail lamp LH (body side) and tail lamp LH (back door side) terminals.
Tail lamp LH (body side)
Tail lamp LH (back door side)
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the corresponding rear combination lamp. Refer to
EXL-174, "Removal and Installation"
.
Component Inspection (License Plate Lamp)
INFOID:0000000010452556
1.
CHECK LICENSE PLATE LAMP
1.
Turn ignition switch OFF.
2.
Disconnect license plate lamp connector.
3.
Check resistance of license plate lamp terminals.
License plate lamp LH
License plate lamp RH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK LICENSE PLATE LAMP
1.
Remove license plate lamp bulb.
2.
Check resistance of license plate lamp terminals.
License plate lamp LH
Stop lamp / tail lamp LH (body side)
Resistance
Terminal
3
2
Except 0
Ω
Tail lamp LH (back door side)
Resistance
Terminal
1
2
Except 0
Ω
License plate lamp LH
Resistance
Terminal
1
2
Except 0
Ω
License plate lamp RH
Resistance
Terminal
1
2
Except 0
Ω
License plate lamp LH
Resistance
Terminal
1
2
Except 0
Ω
B20D4 TAIL LAMP LH POWER SUPPLY CIRCUIT
EXL-107
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
License plate lamp RH
Is the inspection result normal?
YES
>> Replace the corresponding license plate lamp bulb. Refer to
.
NO
>> Repair or replace the corresponding license plate lamp bulb socket.
License plate lamp RH
Resistance
Terminal
1
2
Except 0
Ω
EXL-108
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
B20D5 TAIL LAMP RH POWER SUPPLY CIRCUIT
B20D5 TAIL LAMP RH POWER SUPPLY CIRCUIT
DTC Description
INFOID:0000000010452557
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector
• Rear combination lamp RH (body side) internal circuit
- LED (Tail lamp)
- Harness
• Rear combination lamp RH (back door side) internal circuit
- LED (Tail lamp)
- Harness
• IPDM E/R
FAIL-SAFE
Shuts off the power supply to the following power supply circuits until the parking lamp, license plate lamp, and
tail lamp ON conditions are no longer satisfied.
• Tail lamp RH (body side)
• Tail lamp RH (back door side)
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
With CONSULT
1.
Turn ignition switch ON.
2.
Select “T LAMP RH CIRC MALFUNCTN” in “Data Monitor” mode of “IPDM E/R” using CONSULT.
3.
Check the monitor status.
What is the monitor status?
“0”
>> GO TO 2.
“1”
>> A short circuit is detected multiple times in the tail lamp RH (body side) or tail lamp RH (back door
side) power supply circuit, and damage accumulates at the smart FET inside the IPDM E/R. For
this reason, IPDM E/R does not turn ON the smart FET. Because the DTC cannot be reproduced
in this state, perform
EXL-109, "Diagnosis Procedure"
and replace IPDM E/R after the malfunc-
tioning part is repaired. Refer to
PCS-67, "Removal and Installation"
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch OFF.
2.
Turn ignition switch ON.
3.
Turn lighting switch 1ST.
4.
Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
5.
Check DTC.
Is DTC detected?
YES
>> Refer to
EXL-109, "Diagnosis Procedure"
.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
B20D5
TAIL LAMP RH PWR SPLY CIRC
(Tail lamp right hand power supply circuit)
[CIRC
SHORT TO
GRND]
When the parking lamp, license plate lamp, and tail lamp
ON conditions are satisfied (smart FET inside IPDM E/R
is ON), and overcurrent is detected in the following power
supply circuit.
• Tail lamp RH (body side)
• Tail lamp RH (back door side)
Monitor item
Monitor status
T LAMP RH CIRC MALFUNCTN
0
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст