Nissan Qashqai J11. Manual — part 1180
PRECAUTIONS
SE-3
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
5.
Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse
of the specified time.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
6.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
Service Notice
INFOID:0000000010436318
• When removing or installing various parts, place a cloth or padding onto the vehicle body to prevent
scratches.
• Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to oil or
damage them.
• Apply sealing compound where necessary when installing parts.
• When applying sealing compound, be careful that the sealing compound does not protrude from parts.
• When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust preven-
tion measures.
Precaution for Work
INFOID:0000000010436319
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and keep them.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After re-installation is completed, be sure to check that each part works normally.
• Follow the steps below to clean components.
- Water soluble foul: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the
fouled area.
Then rub with a soft and dry cloth.
- Oily foul: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the fouled area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.
• Never use organic solvent such as thinner, benzene, alcohol, and gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.
D4D engine
: 20 minutes
HRA2DDT
: 12 minutes
K9K engine
: 4 minutes
M9R engine
: 4 minutes
R9M engine
: 4 minutes
V9X engine
: 4 minutes
SE-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000010436320
Tool name
Description
Engine ear
Locates the noise
SIIA0995E
CLIP LIST
SE-5
< PREPARATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
CLIP LIST
Clip List
INFOID:0000000010436321
JMJIA3734GB
SE-6
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
POWER SEAT SYSTEM
POWER SEAT SYSTEM : Component Parts Location
INFOID:0000000010436340
POWER SEAT SYSTEM : Component Description
INFOID:0000000010436341
HEATED SEAT SYSTEM
JMJIA9930ZZ
No.
Component
Function
Sliding motor
With the power supplied from power seat switch, operates the forward and back-
ward slide of seat
Reclining motor
With the power supplied from power seat switch, operates the forward and back-
ward movement of seatback
Lifting motor
With the power supplied from power seat switch, operates the up and down
movement of seat cushion
Power seat switch
Built-in reclining switch, sliding switch and lifting switch, controls the power sup-
plied to each motor
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст