Nissan Qashqai J11. Manual — part 846
FRONT DRIVE SHAFT
FAX-71
< UNIT DISASSEMBLY AND ASSEMBLY >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
8.
Pinch projection on the band with suitable pliers to tighten band.
9.
Insert tip of band below end of the pawl.
10. Secure housing and shaft, and then make sure that they are in
the correct position when rotating boot. Install them with new
boot band when the mounting positions become incorrect.
11. Install dust shield.
CAUTION:
Never reuse dust shield.
12. Install circular clip to housing (left side).
CAUTION:
Never reuse circular clip.
Support Bearing
1.
Install dust shield on housing assembly.
CAUTION:
Never reuse dust shield.
2.
Install support bearing into retainer.
3.
Install snap ring to retainer.
CAUTION:
Never reuse snap ring.
4.
Install retainer and support bearing to housing assembly.
5.
Install snap ring.
CAUTION:
Never reuse snap ring.
6.
Install dust shields.
CAUTION:
Never reuse dust shields.
Dynamic Damper
SDIA3558E
FAC0147D
YAX007
FAC0154D
FAX-72
< UNIT DISASSEMBLY AND ASSEMBLY >
[4WD]
FRONT DRIVE SHAFT
Secure dynamic damper with bands in the following specified posi-
tion when removing.
CAUTION:
Never reuse bands.
Wheel Side
For further details, refer to the installation procedure of “
FAX-54, "WHEEL SIDE : Removal and Installation"
for the drive shaft boot.
Inspection
INFOID:0000000011722648
INSPECTION AFTER REMOVAL
• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-
cant looseness.
• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there
is any non-standard condition.
INSPECTION AFTER DISASSEMBLY
Shaft
Check shaft for runout, cracks, or other damage. Replace if there are.
Dynamic Damper
Check damper for cracks or wear. Replace if necessary.
Joint Sub-Assembly (Wheel Side)
Check the following:
• Joint sub-assembly for rough rotation and excessive axial looseness
• The inside of the joint sub-assembly for entry of foreign material
• Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly
Replace joint sub-assembly if there are any non-standard conditions of components.
Housing and Spider assembly (Transaxle Side)
Replace housing and spider assembly if there is any scratching or wear of housing on roller contact surface or
spider roller contact surface.
NOTE:
Housing and spider assembly are used in a set.
Support Bearing (Right Side)
Make sure wheel bearing rolls freely and is free from noise, cracks, pitting or wear. Replace support bearing if
there are any non-standard conditions.
Support Bearing Bracket (Right Side)
Check for bending, cracks, or damage. Replace support bearing bracket if there are any non-standard condi-
tions.
Standard
.
FAC0156D
SDIA1190J
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-73
< SERVICE DATA AND SPECIFICATIONS (SDS)
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000010436941
Drive Shaft
INFOID:0000000010297882
MR20DD
M/T models
CVT models
Item
Standard
Axial end play
0.0 mm (0.0 in)
Rotating torque
1.9 N.m (0.19 kg-m, 17 in-lb) or less
Spring balance measurement
13.7 N (1.40 kg-f, 3.08 lb-f) or less
Joint
Wheel side
Transaxle assembly side
Grease quantity
Left side
115 – 135 g (4.06 – 4.76 oz)
200 – 220 g (7.05 – 7.76 oz)
Right side
Boots installed length (L)
Left side
133.5 mm (5.26 in)
189.6 mm (7.46 in)
Right side
177.6 mm (6.99 in)
Dynamic damper
A
B
Dimension
Right side
219 – 223 mm (8.62 – 8.78 in)
70 mm (2.76 in)
JPDIF0031ZZ
FAC0156D
Joint
Wheel side
Transaxle assembly side
Grease quantity
Left side
115 – 135 g (4.06 – 4.76 oz)
200 – 220 g (7.05 – 7.76 oz)
Right side
FAX-74
< SERVICE DATA AND SPECIFICATIONS (SDS)
[4WD]
SERVICE DATA AND SPECIFICATIONS (SDS)
R9M
M/T models
Boots installed length (L)
Left side
133.5 mm (5.26 in)
185.6 mm (7.31 in)
Right side
177.6 mm (6.99 in)
Dynamic damper
A
B
Dimension
Right side
238 – 242 mm (9.37 – 9.53 in)
70 mm (2.76 in)
JPDIF0031ZZ
FAC0156D
Joint
Wheel side
Transaxle assembly side
Grease quantity
Left side
175 – 205 g (6.17 – 7.23 oz)
165 – 175 g (5.82 – 6.17 oz)
Right side
Boots installed length (L)
Left side
163.4 mm (6.43 in)
173.1 mm (6.81 in)
Right side
181.1 mm (7.13 in)
Dynamic damper
A
B
JPDIF0031ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст