Nissan Qashqai J11. Manual — part 2202
DAS-222
< SYSTEM DESCRIPTION >
[CHASSIS CONTROL]
DIAGNOSIS SYSTEM (CHASSIS CONTROL MODULE)
ATC 2
[Off / On]
Displays active trace control function operating status.
ATC 4
[Off / On]
Displays active trace control function operating status.
BRAKE HOLD
[INACT / ACT / RELEA]
Displays the status of Hill Start Assist function.
ATC 3
[Off / On]
Displays active trace control function operating status.
ATC 5
[Off / On]
Displays active trace control function operating status.
ARC BRAKE
[Off / On]
Displays the brake control effect of Active Trace Control function on the informa-
tion display in the combination meter.
FL TIRE DISP
[DEF / 1]
Displays tire status.
FR TIRE DISP
[DEF / 1]
Displays tire status.
RL TIRE DISP
[DEF / 1]
Displays tire status.
RR TIRE DISP
[DEF / 1]
Displays tire status.
VEHICLE DISP
[Off / On]
Displays Active Ride Control (brake) activation status.
INTERRUPT DISP
[NOREQ / HOLD1 / HOLD2 / HDC]
Displays the interruption status.
TURN DISP
[NSTEER / LEFT / RIGHT]
Displays the turn status.
ALC LEVEL
[0]
Displayed but not used.
ALC STATUS
[ACTIVE / INACT]
Displayed but not used.
BRAKE HOLD DISP
[INACT / ACT / RELEA]
Displays the brake hold status.
ATC DISP
[Off / On]
Displays Active Trace Control status.
ARC BRAKE DISP
[Off / On]
Displays the status of Active Ride Control (brake).
HDC DISP
[Off / On]
Displays the Hill Descent Control.
AEB CVT PERMIT
[Off / On]
Displays the CVT authorized state for Active Engine Brake.
AEB STATUS
[Off / On]
Displays the Active Engine Brake status.
AEB COMMAND 1
[0.0000]
Displays the relative command value of Active Engine Brake.
AEB COMMAND 2
[0.0000]
Displays absolute command value of Active Engine Brake.
AEB SLIP RATE
[%]
Displays slip ratio of Active Engine Brake.
ATC SETTING
[Off / On]
Displays Active Trace Control state on METER.
AEB SETTING
[Off / On]
Displays Active Engine Brake state on METER.
Item
[Unit]
Description
DAS
DIAGNOSIS SYSTEM (CHASSIS CONTROL MODULE)
DAS-223
< SYSTEM DESCRIPTION >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ACTIVE TEST
The active test is used to determine and identify details of a malfunction, based on self-diagnosis test results
and data obtained in the DATA MONITOR. In response to instructions from CONSULT, instead of those from
chassis control module on the vehicle, a drive signal is sent to the actuator to check its operation.
CAUTION:
• Never perform ACTIVE TEST while driving the vehicle.
• Always bleed air from brake system before active test.
• Never perform active test when system is malfunctioning.
NOTE:
• When active test is performed while depressing the brake pedal, the brake pedal depressing stroke may
change. This is not a malfunction.
• During an active test, sometimes a chassis control warning is displayed and the master warning lamp illumi-
nates on the information display in the combination meter; however, this is not a malfunction.
Test item
Operation
Description
BRAKE ACTUATOR 1 MODE 1
Start
Controls brake fluid pressure.
BRAKE ACTUATOR 1 MODE 2
Start
Controls brake fluid pressure.
BRAKE ACTUATOR 1 MODE 3
Start
Controls brake fluid pressure.
BRAKE ACTUATOR 2 MODE 1
Start
Controls brake fluid pressure.
BRAKE ACTUATOR 2 MODE 2
Start
Controls brake fluid pressure.
BRAKE ACTUATOR 2 MODE 3
Start
Controls brake fluid pressure.
BRAKE ACTUATOR 3 MODE 1
Start
Controls brake fluid pressure.
BRAKE ACTUATOR 3 MODE 2
Start
Controls brake fluid pressure.
BRAKE ACTUATOR 3 MODE 3
Start
Controls brake fluid pressure.
MASTER WARNING ACTIVE
On
If touching “On” with the master warning lamp not illuminated, the master warn-
ing lamp illuminates. Stops in approximately 1 minute.
Off
The master warning lamp turns OFF. (vehicle in normal state)
FL TIRE DISP
On
Displays the front LH tire on the information display in the combination meter.
Off
Does not display the front LH tire on the information display in the combination
meter.
FR TIRE DISP
On
Displays the front RH tire on the information display in the combination meter.
Off
Does not display the front RH tire on the information display in the combination
meter.
RL TIRE DISP
On
Displays the rear LH tire on the information display in the combination meter.
Off
Does not display the rear LH tire on the information display in the combination
meter.
RR TIRE DISP
On
Displays the rear RH tire on the information display in the combination meter.
Off
Does not display the rear RH tire on the information display in the combination
meter.
TURN DISP
NO DISP
Does not display the turning status on the information display in the combina-
tion meter.
LH
Displays the LH turning status on the information display in the combination
meter.
RH
Displays the RH turning status on the information display in the combination
meter.
ROUND
Displayed but not used.
ATC 1 DISP
On
Displays active trace control function active status on the information display in
the combination meter.
Off
Displays active trace control function inactive status on the information display
in the combination meter.
DAS-224
< SYSTEM DESCRIPTION >
[CHASSIS CONTROL]
DIAGNOSIS SYSTEM (CHASSIS CONTROL MODULE)
RE/PROGRAMMING, CONFIGURATION
Configuration includes the following functions.
CAUTION:
Use “Manual Configuration” only when “TYPE ID” of Chassis Control Module cannot be read.
ATC 2 DISP
On
Displays active trace control function active status on the information display in
the combination meter.
Off
Displays active trace control function inactive status on the information display
in the combination meter.
HDC DISP
On
Displays Hill Descent Control active status on the information display on the
combination meter.
Off
Displays Hill Descent Control inactive status on the information display on the
combination meter.
BRAKE HOLD DISP
INACT
Displays inactive status of controls on the information display on the combina-
tion meter.
READY
Displays ready status of Hill Start Assist on the information display on the com-
bination meter.
ACTIVE
Displays active status of Hill Start Assist on the information display on the com-
bination meter.
ERROR
Displays inactive status of controls on the information display on the combina-
tion meter.
AEB DISP
On
Displays Active Engine Brake (corner) active status on the information display
in the combination meter.
Off
Displays Active Engine Brake (corner) inactive status on the information dis-
play in the combination meter.
VEHICLE DISP
On
Displays Active Ride Control (brake) active status on the information display in
the combination meter.
Off
Displays Active Ride Control (brake) inactive status on the information display
in the combination meter.
INTERRUPT DISP
NO REQ
Displays inactive status of controls on the information display in the combina-
tion meter.
READY
Displays ready status of Hill Start Assist on the information display in the com-
bination meter.
ACTIVE
Displays active status of Hill Start Assist on the information display in the com-
bination meter.
HDC
Displays Hill Descent Control active status on the information display in the
combination meter.
ATC 3 DISP
On
Displays active trace control function active status on the information display in
the combination meter.
Off
Displays active trace control function inactive status on the information display
in the combination meter.
Test item
Operation
Description
Function
Description
Read/Write Configuration
Before replacing ECU
Allows the reading of vehicle specification (Type ID) written in Chassis Con-
trol Module to store the specification in CONSULT.
After replacing ECU
Allows the writing of vehicle information (Type ID) stored in CONSULT into
the Chassis Control Module.
Manual Configuration
Allows the writing of vehicle specification (Type ID) into the Chassis Control
Module by hand.
DAS
CHASSIS CONTROL MODULE
DAS-225
< ECU DIAGNOSIS INFORMATION >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ECU DIAGNOSIS INFORMATION
CHASSIS CONTROL MODULE
Reference Value
INFOID:0000000010416976
CONSULT DATA MONITOR STANDARD VALUE
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor item
Condition
Reference values in normal operation
IGN VOLT
Ignition switch ON
10
−
16 V
CONTROL MODULE MALF
When chassis control module is normal
Off
When chassis control module malfunction is
detected
On
CAN DIAG STATUS
When diagnosis of CAN communication mal-
function is detected
Off
When diagnosis of CAN communication is nor-
mal
On
STP LAMP OFF RELAY 1
Displayed but not used.
—
STP LAMP OFF RELAY 2
Displayed but not used.
—
ESS RELAY
Displayed but not used.
—
VEHICLE SPEED
Vehicle Stopped
0 km/h (0 MPH)
Driving
*
Almost same reading as speedometer
(within
±
10%)
FR WHEEL SPEED
Vehicle stopped
0 rpm
Driving
*
Increases according to vehicle speed
FL WHEEL SPEED
Vehicle stopped
0 rpm
Driving
*
Increases according to vehicle speed
RR WHEEL SPEED
Vehicle stopped
0 rpm
Driving
*
Increases according to vehicle speed
RL WHEEL SPEED
Vehicle stopped
0 rpm
Driving
*
Increases according to vehicle speed
STEERING ANG SENSOR
When driving straight
0
±
3.5 deg
When steering wheel is steered to RH by 90
°
Approx. +90 deg
When steering wheel is steered to LH by 90
°
Approx.
−
90 deg
DECEL G SENSOR
Vehicle stopped
Approx. 0 G
When during acceleration
Positive value
When during deceleration
Negative value
SIDE G SENSOR
Vehicle stopped
Approx. 0 G
When right turn
Negative value
When left turn
Positive value
YAW RATE SENSOR
Vehicle stopped
Approx. 0 deg/s
When right turn
Negative value
When left turn
Positive value
ACCELE PEDAL POSITION
When accelerator pedal is released
0%
When accelerator pedal is depressed
0
−
100%
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст