Nissan Qashqai J11. Manual — part 73
CYLINDER BLOCK
EM-231
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
18. Install oil filter (for intake valve timing control)
in the direction
shown in the figure.
• Check that the oil filter (for intake valve timing control) does
not protrude from the upper surface of cylinder block
after
installation.
19. Assemble in the reverse order of disassembly.
Inspection
INFOID:0000000010715517
CRANKSHAFT END PLAY
• Measure the clearance between thrust bearings and crankshaft
arm when crankshaft is moved fully forward or backward with a dial
indicator (A).
• If the measured value exceeds the limit, replace thrust bearings,
and measure again. If it still exceeds the limit, replace crankshaft
also.
CONNECTING ROD SIDE CLEARANCE
• Measure the side clearance between connecting rod and crank-
shaft arm with a feeler gauge (A).
• If the measured value exceeds the limit, replace connecting rod,
and measure again. If it still exceeds the limit, replace crankshaft
also.
PISTON TO PISTON PIN OIL CLEARANCE
Piston Pin Hole Diameter
Measure the inner diameter of piston pin hole with an inside
micrometer (A).
Piston Pin Outer Diameter
PBIC3260J
Standard and Limit
: Refer to
.
JSBIA2509ZZ
Standard and Limit
: Refer to
.
JPBIA0689ZZ
Standard
: Refer to
.
JSBIA2510ZZ
EM-232
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR20DD]
CYLINDER BLOCK
Measure the outer diameter of piston pin with a micrometer (A).
Piston to Piston Pin Oil Clearance
(Piston to piston pin oil clearance) = (Piston pin hole diameter) – (Piston pin outer diameter)
• If oil clearance is out of the standard, replace piston and piston pin assembly.
• When replacing piston and piston pin assembly. Refer to
.
NOTE:
• Piston is available together with piston pin as assembly.
• Piston pin (piston pin hole) grade is provided only for the parts installed at the plant. For service parts, no
grades can be selected. (Only grade “0” is available.)
PISTON RING SIDE CLEARANCE
• Measure the side clearance of piston ring and piston ring groove
with a feeler gauge (A).
• If the measured value exceeds the limit, replace piston ring, and
measure again. If it still exceeds the limit, replace piston also.
PISTON RING END GAP
• Check that cylinder bore inner diameter is within specification. Refer to “PISTON TO CYLINDER BORE
CLEARANCE”.
• Lubricate with new engine oil to piston
and piston ring
, and
then insert
piston ring until middle of cylinder
with piston, and
measure piston ring end gap with a feeler gauge (C).
• If the measured value exceeds the limit, replace piston ring, and
measure again. If it still exceeds the limit, rebore cylinder and use
oversized piston and piston rings.
CONNECTING ROD BEND AND TORSION
Standard :
Refer
JSBIA2511ZZ
Standard :
Standard and Limit
: Refer to
JSBIA2512ZZ
Standard and Limit
: Refer to
JSBIA2513ZZ
CYLINDER BLOCK
EM-233
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Check with a connecting rod aligner.
• If it exceeds the limit, replace connecting rod assembly.
CONNECTING ROD BIG END DIAMETER
• Install connecting rod cap
without connecting rod bearing
installed, and tightening connecting rod cap bolts to the specified
torque. Refer to
EM-223, "Disassembly and Assembly"
.
• Measure the inner diameter of connecting rod big end with an
inside micrometer.
• If out of the standard, replace connecting rod assembly.
CONNECTING ROD BUSHING OIL CLEARANCE
Connecting Rod Bushing Inner Diameter
Measure the inner diameter of connecting rod bushing with an inside
micrometer (A).
Piston Pin Outer Diameter
: Bend
: Torsion
C
: Feeler gauge
Limit
.
JSBIA2514ZZ
: Connecting rod
: Example
: Measuring direction of inner diameter
Standard :
PBIC3269J
Standard :
JPBIA0223ZZ
EM-234
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR20DD]
CYLINDER BLOCK
Measure the outer diameter of piston pin with a micrometer (A).
Connecting Rod Bushing Oil Clearance
(Connecting rod bushing oil clearance) = (Connecting rod bushing inner diameter) – (Piston pin outer diame-
ter)
• If the measured value is out of the standard, replace connecting rod assembly and/or piston and piston pin
assembly.
• If replacing piston and piston pin assembly. Refer to
.
• If replacing connecting rod assembly. Refer to
EM-241, "Connecting Rod Bearing"
.
CYLINDER BLOCK TOP SURFACE DISTORTION
• Using a scraper, remove gasket on the cylinder block surface, and also remove engine oil, scale, carbon, or
other contamination.
CAUTION:
Be careful not to allow gasket flakes to enter engine oil or engine coolant passages.
• Measure the distortion on the cylinder block upper face at some
different points in six directions with a straight edge (A) and feeler
gauge (B).
• If it exceeds the limit, replace cylinder block.
MAIN BEARING HOUSING INNER DIAMETER
• Install main bearing cap without main bearings installed, and tighten main bearing cap mounting bolts to the
specified torque. Refer to
EM-223, "Disassembly and Assembly"
• Measure the inner diameter of main bearing housing with a cylinder gauge.
• Measure the position shown in the figure [5 mm (0.20 in)] back-
ward from main bearing housing front side in the 2 directions as
shown in the figure. The smaller one is the measured value.
• If out of the standard, replace cylinder block and main bearing
caps assembly.
NOTE:
Main bearing caps cannot be replaced as a single, because it is machined together with cylinder block.
PISTON TO CYLINDER BORE CLEARANCE
Standard :
JSBIA2511ZZ
Standard and Limit
: Refer to
Limit :
Refer
.
JSBIA2526ZZ
: Cylinder block
: Main bearing cap
: Engine front
Standard :
PBIC4005E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст