Nissan Qashqai J11. Manual — part 1271
REAR DOOR
DLK-353
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5.
Remove check link mounting bolts of door side.
6.
Take door check link out from the hole of door panel.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check front door open/close operation after installation.
• After installation, check door check link rotating part for poor lubrication. Refer to
DOOR CHECK LINK : Inspection
INFOID:0000000010478259
Check door hinge rotating part for poor lubrication. Apply body
grease if necessary.
: Body grease
JMKIB0322ZZ
DLK-354
< REMOVAL AND INSTALLATION >
[TYPE 2]
BACK DOOR
BACK DOOR
Exploded View
INFOID:0000000010478260
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010478261
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• Use protective tape or shop cloth to protect from damage during removal and installation.
1.
Back door hinge
2.
Stud ball
3.
Back door stay
4.
Back door weather-strip
5.
Stud ball
6.
Back door bumper rubber
7.
Back door striker
8.
TORX bolt
9.
Back door panel
A.
Center mark
B.
Seam
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
,
,
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB3637GB
BACK DOOR
DLK-355
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOVAL
1.
Remove back door trim finisher lower and back door trim finisher upper. Refer to
.
2.
Remove rear washer tube from back door panel. Refer to
WW-90, "WASHER TUBE : Removal and Instal-
.
3.
Disconnect back door harness connectors from body harness connectors.
4.
Remove harness grommet from back door panel.
5.
Pull out body harness LH from back door panel.
6.
Support back door with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
7.
Remove back door stay of back door side. Refer to
DLK-358, "BACK DOOR STAY : Removal and Installa-
8.
Remove back door mounting nuts, and then remove back door assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, perform the fitting adjustment. Refer to
DLK-355, "BACK DOOR ASSEMBLY :
• Apply touch-up paint to the body color if the paint around back door hinge is peeled off.
• Check back door hinge rotating part for poor lubrication. Refer to
BACK DOOR ASSEMBLY : Adjustment
INFOID:0000000010478262
FITTING ADJUSTMENT
DLK-356
< REMOVAL AND INSTALLATION >
[TYPE 2]
BACK DOOR
Fitting Adjustment Standard
Check the clearance and the surface height between back door and each part by seeing and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1.
Roof panel
2.
Body side outer
3.
Rear bumper fascia
4.
Back door panel
5.
Back door hinge
6.
Back door bumper rubber
7.
Back door striker
8.
TORX bolt
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Body grease
JMKIB3321GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст