Nissan Qashqai J11. Manual — part 2121
AV
NAVIGATION SYSTEM
AV-173
< WIRING DIAGRAM >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
JRNWD1443GB
AV-174
< BASIC INSPECTION >
[NAVIGATION]
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000010435667
OVERALL SEQUENCE
DETAILED FLOW
1.
GET INFORMATION FOR SYMPTOM
Get detailed information from the customer about the symptom (the condition and the environment when the
incident/malfunction occurred).
>> GO TO 2.
2.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer. Verify relation between the symptom and the condition
when the symptom is detected.
>> GO TO 3.
3.
PERFORM SELF DIAGNOSTIC RESULT
1.
Turn ignition switch ON and wait for 2 seconds or more.
AWNIA2982GB
AV
DIAGNOSIS AND REPAIR WORKFLOW
AV-175
< BASIC INSPECTION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
2.
Depending on system being diagnosed, perform Self Diagnostic Result for:
-
MULTI AV.
-
AVM.
Are any DTCs displayed?
YES
>> Refer to
(MULTI AV) or
AV-154, "WITHOUT DRIVER ASSISTANCE SYS-
(AVM).
NO
>> GO TO 4.
4.
PERFORM SYMPTOM DIAGNOSIS
>> GO TO 5.
5.
FINAL CHECK
Refer to symptom described by the customer in step 1.
Is the symptom still present?
YES
>> GO TO 2.
NO
>> Inspection End.
AV-176
< BASIC INSPECTION >
[NAVIGATION]
INSPECTION AND ADJUSTMENT
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING AV CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING AV CONTROL UNIT : Description
INFOID:0000000010435668
BEFORE REPLACEMENT
When replacing AV control unit, save or print current vehicle specification with CONSULT configuration before
replacement.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replac-
ing AV control unit.
AFTER REPLACEMENT
CAUTION:
When replacing AV control unit, you must perform “After Replace ECU” with CONSULT.
• Complete the procedure of “After Replace ECU” in order.
• If you set incorrect “After Replace ECU”, incidents might occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
ADDITIONAL SERVICE WHEN REPLACING AV CONTROL UNIT : Work Procedure
INFOID:0000000010435669
1.
SAVING VEHICLE SPECIFICATION
-CONSULT
Enter “Re/Programming, Configuration” and perform “Before Replace ECU” to save or print current vehicle
specification.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replac-
ing AV control unit.
>> GO TO 2.
2.
REPLACE AV CONTROL UNIT
Replace AV control unit. Refer to
AV-259, "Removal and Installation"
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT
1.
Enter "Re/Programming, Configuration".
2.
If “Before Replace ECU” operation was performed, automatically an "Operation Log Selection" screen will
be displayed. Select the applicable file from the "Saved Data List" and press “Confirm” to write vehicle
specification. Refer to
AV-178, "CONFIGURATION (AV CONTROL UNIT) : Work Procedure"
.
3.
If “Before Replace ECU” operation was not performed, select "After Replace ECU" or "Manual Configura-
tion" to write vehicle specification. Refer to
AV-178, "CONFIGURATION (AV CONTROL UNIT) : Work Pro-
>> GO TO 4.
4.
OPERATION CHECK
Check that the operation of the AV control unit and camera images (fixed guide lines) are normal.
>> Work End.
ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR CON-
TROL UNIT
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст