Nissan Qashqai J11. Manual — part 2058
SN-26
< BASIC INSPECTION >
[WITHOUT PARKING SPACE MEASUREMENT]
DIAGNOSIS AND REPAIR WORKFLOW
NOTE:
Skip to step 4 of the diagnosis procedure if SONAR is not displayed.
2.
When DTC is detected, follow the instructions below:
-
Record DTC and Freeze Frame Data.
Is DTC displayed?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
TROUBLE DIAGNOSIS FOR DTC
1.
Check the DTC indicated in the self-diagnosis results.
2.
Perform the relevant diagnosis referring to the DTC Index. Refer to
.
>> GO TO 5.
4.
TROUBLE DIAGNOSIS FOR SYMPTOMS
Perform the relevant diagnosis referring to the diagnosis chart by symptom. Refer to
.
>> GO TO 5.
5.
ERROR PART REPAIR
1.
Repair or replace the identified malfunctioning parts.
2.
Perform Self Diagnostic Result for SONAR with CONSULT.
NOTE:
Erase the stored self-diagnosis results after repairing or replacing the relevant components if any DTC
has been indicated in the self-diagnosis results.
3.
Check that the symptom does not occur.
Does the symptom occur?
YES
>> GO TO 1.
NO
>> Inspection End.
SN
INSPECTION AND ADJUSTMENT
SN-27
< BASIC INSPECTION >
[WITHOUT PARKING SPACE MEASUREMENT]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING SONAR CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING SONAR CONTROL UNIT : Description
INFOID:0000000010435922
BEFORE REPLACEMENT
When replacing sonar control unit, save or print current vehicle specification with CONSULT configuration
before replacement.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replac-
ing sonar control unit.
AFTER REPLACEMENT
CAUTION:
When replacing sonar control unit, you must perform “After Replace ECU” with CONSULT.
• Complete the procedure of “After Replace ECU” in order.
• If you set incorrect “After Replace ECU”, incidents might occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
ADDITIONAL SERVICE WHEN REPLACING SONAR CONTROL UNIT : Work Proce-
dure
INFOID:0000000010435923
1.
SAVING VEHICLE SPECIFICATION
-CONSULT
Enter “Re/Programming, Configuration” and perform “Before Replace ECU” to save or print current vehicle
specification.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replac-
ing sonar control unit.
>> GO TO 2.
2.
REPLACE SONAR CONTROL UNIT
Replace sonar control unit. Refer to
SN-51, "Removal and Installation"
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT
1.
Enter "Re/Programming, Configuration".
2.
If “Before Replace ECU” operation was performed, an "Operation Log Selection" screen will automatically
be displayed. Select the applicable file from the "Saved Data List" and press “Confirm” to write vehicle
specification. Refer to
SN-28, "CONFIGURATION (SONAR CONTROL UNIT) : Work Procedure"
.
3.
If “Before Replace ECU” operation was not performed, select "After Replace ECU" or "Manual Configura-
tion" to write vehicle specification. Refer to
SN-28, "CONFIGURATION (SONAR CONTROL UNIT) : Work
>> GO TO 4.
4.
OPERATION CHECK
Check that the operation of the sonar control unit is normal.
>> Work End.
CONFIGURATION (SONAR CONTROL UNIT)
SN-28
< BASIC INSPECTION >
[WITHOUT PARKING SPACE MEASUREMENT]
INSPECTION AND ADJUSTMENT
CONFIGURATION (SONAR CONTROL UNIT) : Description
INFOID:0000000010435924
Vehicle specification needs to be written with CONSULT. Configuration has three functions as follows:
CAUTION:
• When replacing sonar control unit, you must perform “Select Saved Data List” or "After Replace
ECU" with CONSULT.
• Complete the procedure of “Select Saved Data List” or "After Replace ECU" in order.
• If you set incorrect “Select Saved Data List” or "After Replace ECU", incidents might occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “Select Saved Data List” or "After Replace ECU" except for new sonar control unit.
CONFIGURATION (SONAR CONTROL UNIT) : Work Procedure
INFOID:0000000010435925
1.
WRITING MODE SELECTION
CONSULT
Select “Reprogramming, Configuration” of sonar control unit.
When writing saved data>>GO TO 2.
When writing manually>>GO TO 3.
2.
PERFORM “SAVED DATA LIST”
CONSULT
Automatically “Operation Log Selection” window will display if “Before Replace ECU” was performed. Select
applicable file from the “Save Data List” and press “Confirm”.
>> Work End.
3.
PERFORM “AFTER REPLACE ECU” OR “MANUAL CONFIGURATION”
CONSULT
1.
Select “After Replace ECU” or “Manual Configuration”.
2.
Identify the correct model and configuration list. Refer to
SN-29, "CONFIGURATION (SONAR CONTROL
3.
Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally
if the setting is not correct.
4.
Select “Next”.
CAUTION:
Make sure to select “Next”, confirm each setting value and press “OK” even if the indicated con-
figuration of brand new sonar control unit is same as the desirable configuration. If not, configura-
tion which is set automatically by selecting vehicle model can not be memorized.
5.
When "Completed", select "End".
>> GO TO 4.
4.
OPERATION CHECK
Confirm that each function controlled by sonar control unit operates normally.
>> Work End.
Function
Description
"Before Replace ECU"
• Reads the vehicle configuration of current sonar control unit.
• Saves the read vehicle configuration.
"After Replace ECU"
Writes the vehicle configuration with manual selection.
"Select Saved Data List"
Writes the vehicle configuration with saved data.
SN
INSPECTION AND ADJUSTMENT
SN-29
< BASIC INSPECTION >
[WITHOUT PARKING SPACE MEASUREMENT]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
CONFIGURATION (SONAR CONTROL UNIT) : Configuration List
INFOID:0000000010435926
CAUTION:
Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnormal
control of ECU.
⇔
: Items which confirm vehicle specifications
MANUAL SETTING ITEM
Items
Setting value
BCI FUNCTION
WITH
⇔
WITHOUT
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст