Nissan Qashqai J11. Manual — part 1203
BACK DOOR REQUEST SWITCH
DLK-81
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR REQUEST SWITCH
Component Function Check
INFOID:0000000010479676
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “REQ SW-BD/TR” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Back door request switch is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000010479677
1.
CHECK BACK DOOR REQUEST SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect back door opener switch assembly connector.
3.
Check voltage between back door opener switch assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR REQUEST SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and back door opener switch assembly harness con-
nector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair harness or connector.
3.
CHECK BACK DOOR REQUEST SWITCH GROUND CIRCUIT
Check continuity between back door opener switch assembly harness connector and ground.
Monitor item
Condition
Status
REQ SW-BD/TR
Back door request switch
Pressed
On
Released
Off
(+)
(–)
Voltage
Back door opener switch assembly
Connector
Terminal
D94
2
Ground
9 - 16 V
BCM
Back door opener switch assembly
Continuity
Connector
Terminal
Connector
Terminal
B4
6
D94
2
Existed
BCM
Ground
Continuity
Connector
Terminal
B4
6
Not existed
DLK-82
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
BACK DOOR REQUEST SWITCH
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK BACK DOOR REQUEST SWITCH
DLK-82, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace back door opener switch assembly.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000010479678
1.
CHECK BACK DOOR REQUEST SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect back door opener switch assembly connector.
3.
Check continuity between back door opener switch assembly terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace back door opener switch assembly.
Back door opener switch assembly
Ground
Continuity
Connector
Terminal
D94
3
Existed
Back door opener switch assembly
Condition
Continuity
Terminal
2
3
Back door request switch
Pressed
Existed
Released
Not existed
COMBINATION METER BUZZER
DLK-83
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
COMBINATION METER BUZZER
Component Function Check
INFOID:0000000010434580
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “INSIDE BUZZER” in “ACTIVE TEST” mode.
3.
Touch “Buzzer 1”, “Buzzer 2” or “Buzzer 3” to check that it works normally.
Is the inspection result normal?
Yes
>> Buzzer (combination meter) is OK.
No
>> Refer to
.
Diagnosis Procedure
INFOID:0000000010434581
1.
CHECK METER BUZZER CIRCUIT
WCS-44, "Component Function Check"
.
Is the inspection result normal?
Yes
>> GO TO 2.
No
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
D L K -8 4
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
DOOR LOCK ACTUATOR
DOOR LOCK ACTUATOR
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000010434582
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “DOOR LOCK” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-84, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000010434583
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check voltage between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock assembly (driver side).
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and all door lock assembly connector.
2.
Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
Monitor item
Status
DOOR LOCK
ALL LOCK
Door lock actuators
LOCK
ALL UNLOCK
UNLOCK
(+)
(–)
Condition
Voltage
Front door lock assembly
(driver side)
Connector
Terminal
D26
2
Ground
Door lock and unlock switch
Unlock
9 – 16 V
3
Lock
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M68
141
D26
3
Existed
148
2
BCM
Ground
Continuity
Connector
Terminal
M68
141
Not existed
148
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст