Nissan Qashqai J11. Manual — part 2168
DAS-86
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
ADDITIONAL SERVICE WHEN REPLACING DISTANCE SENSOR
ADDITIONAL SERVICE WHEN REPLACING DISTANCE SENSOR
Description
INFOID:0000000010416815
Always perform the following after removing and installing or replacing the Distance sensor:
• Distance sensor initial vertical alignment
• Distance sensor alignment
•
CAUTION:
The system does not operate normally unless the Distance sensor is aligned properly.
Work Procedure
INFOID:0000000010416816
1.
DISTANCE SENSOR INITIAL VERTICAL ALIGNMENT
Perform the distance sensor initial vertical alignment. Refer to
.
>> GO TO 2.
2.
DISTANCE SENSOR ALIGNMENT
Perform the distance sensor alignment. Refer to
.
>> Work End.
DAS
ADDITIONAL SERVICE WHEN REPLACING FRONT CAMERA UNIT
DAS-87
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ADDITIONAL SERVICE WHEN REPLACING FRONT CAMERA UNIT
Description
INFOID:0000000010609506
Always adjust the camera aiming after removing and installing or replacing the front camera unit.
CAUTION:
The system does not operate normally unless the camera aiming adjustment is performed. Always
perform it.
Work Procedure
INFOID:0000000010609507
1.
CAMERA AIMING ADJUSTMENT
Perform the camera aiming adjustment with CONSULT. Refer to
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
Perform the self-diagnosis of front camera unit with CONSULT. Check if any DTC is detected.
Is any DTC detected?
YES
>> Perform the trouble diagnosis for the detected DTC. Refer to
.
NO
>> GO TO 3.
3.
LDW ACTION TEST
1.
Perform the LDW action test. Refer to
.
2.
Check that the LDW operates normally.
>> Work End.
DAS-88
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
DISTANCE SENSOR INITIAL VERTICAL ALIGNMENT
DISTANCE SENSOR INITIAL VERTICAL ALIGNMENT
Description
INFOID:0000000010416817
WARNING:
Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should
contact the electric medical equipment manufacturer for the possible influences before use.
OUTLINE OF DISTANCE SENSOR INITIAL ALIGNMENT PROCEDURE
• Always perform the Distance sensor initial vertical alignment after removing and installing or replacing the
Distance sensor.
CAUTION:
The system does not operate normally unless the Distance sensor is aligned properly.
1.
Required tools, refer to
2.
Preparation, refer to
3.
Distance sensor initial vertical alignment, refer to
DAS-89, "Distance Sensor Initial Vertical Alignment"
CAUTIONARY POINT FOR DISTANCE SENSOR ALIGNMENT PROCEDURE
CAUTION:
• For Distance sensor alignment procedure, choose a level location with a few feet of working space in
front and surrounding the vehicle.
• Vehicle must be stationary and unoccupied during the whole alignment procedure.
• Never enter the vehicle during distance sensor alignment.
• For proper system operation and adjustment, all vehicle wheels must be the original factory size.
The Distance sensor requires alignment whenever the Distance sensor is removed and reinstalled and when-
ever front end structural repairs are performed. Distance sensor alignment consists of performing the mechan-
ical vertical alignment (Distance sensor initial vertical alignment) described in the following procedure,
followed by the electronic horizontal alignment (Distance sensor alignment) that is performed using CONSULT
and the appropriate special service tools.
Required Tools
INFOID:0000000010416818
The following tool is necessary to perform the Distance sensor initial vertical alignment:
• Carpenters level.
Preparation
INFOID:0000000010416819
1.
PREPARATION FOR DISTANCE SENSOR INITIAL VERTICAL ALIGNMENT PROCEDURE
1.
Verify correct vehicle suspension height. Refer to
.
2.
Repair or replace any damaged body components.
3.
Verify proper tire inflation pressures. Refer to
.
4.
Remove any accumulations of mud, snow or ice from the vehicle underbody.
5.
Verify that there is no load in the vehicle (cargo or passenger).
6.
Place the vehicle on a known level horizontal surface such as a wheel or frame alignment rack to achieve
satisfactory sensor vertical alignment results.
7.
Remove front fascia. Refer to
EXT-19, "Removal and Installation"
AWOIA0048ZZ
DAS
DISTANCE SENSOR INITIAL VERTICAL ALIGNMENT
DAS-89
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
>> Refer to
DAS-89, "Distance Sensor Initial Vertical Alignment"
.
Distance Sensor Initial Vertical Alignment
INFOID:0000000010416820
NOTE:
The Distance sensor initial vertical alignment procedure must be performed anytime the Distance sensor is
removed and reinstalled.
1.
The Distance sensor (1) is located near the right front head lamp
behind the front bumper fascia.
2.
Place the carpenters level (2) against the face of the Distance
sensor (1).
3.
Turn the Distance sensor adjustment screw (3) to level the sen-
sor.
4.
Insure the Distance sensor electrical connector located on the bottom of the sensor is connected.
5.
Reinstall the front bumper fascia.
6.
Perform the Distance sensor alignment procedure. Refer to
.
AWOIA0049ZZ
AWOIA0050ZZ
AWOIA0051ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст