Nissan Qashqai J11. Manual — part 1694
B1231 DAYTIME RUNNING LIGHT RH POWER SUPPLY CIRCUIT
EXL-77
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
B1231 DAYTIME RUNNING LIGHT RH POWER SUPPLY CIRCUIT
DTC Description
INFOID:0000000010452598
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector
• Front combination lamp RH internal circuit
- LED (Daytime running light)
- Control circuit
- Harness
• IPDM E/R
FAIL-SAFE
Shuts off the power supply to the daytime running light RH power supply circuit until the daytime running light
ON conditions are no longer satisfied.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
With CONSULT
1.
Turn ignition switch ON.
2.
Select “DTRL RH CIRC MALFUNCTN” in “Data Monitor” mode of “IPDM E/R” using CONSULT.
3.
Check the monitor status.
What is the monitor status?
“0”
>> GO TO 2.
“1”
>> A short circuit is detected multiple times in the daytime running light RH power supply circuit, and
damage accumulates at the smart FET inside the IPDM E/R. For this reason, IPDM E/R does not
turn ON the smart FET. Because the DTC cannot be reproduced in this state, perform
and replace IPDM E/R after the malfunctioning part is repaired. Refer to
PCS-67, "Removal and Installation"
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch OFF.
2.
Start engine.
3.
Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
4.
Check DTC.
Is DTC detected?
YES
>> Refer to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010452599
1.
CHECK DAYTIME RUNNING LIGHT RH POWER SUPPLY CIRCUIT (SHORT)
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
B1231
DTRL RH PWR SPLY CIRC
(Daytime running light right hand power
supply circuit)
[CIRC
SHORT TO
GRND]
When daytime running light ON conditions are satisfied
(smart FET inside IPDM E/R is ON), and overcurrent is
detected in the daytime running light RH power supply cir-
cuit.
Monitor item
Monitor status
DTRL RH CIRC MALFUNCTN
0
1
EXL-78
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
B1231 DAYTIME RUNNING LIGHT RH POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and front combination lamp RH connector.
3.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK DAYTIME RUNNING LIGHT RH POWER SUPPLY
With CONSULT
1.
Connect IPDM E/R connector.
2.
Turn ignition switch ON
3.
Select “DAYTIME RUNNING LIGHT” in “Active Test” mode of “IPDM E/R” using CONSULT.
4.
With operating the test items, check the voltage between front combination lamp RH harness connector
and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace IPDM E/R. Refer to
PCS-67, "Removal and Installation"
3.
CHECK DAYTIME RUNNING LIGHT RH
Check the daytime running light RH. Refer to
EXL-78, "Component Inspection"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front combination lamp RH. Refer to
EXL-161, "Removal and Installation"
Component Inspection
INFOID:0000000010452600
1.
CHECK DAYTIME RUNNING LIGHT RH
1.
Turn ignition switch OFF.
2.
Disconnect front combination lamp RH connector.
3.
Check resistance of front combination lamp RH terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front combination lamp RH. Refer to
EXL-161, "Removal and Installation"
IPDM E/R
—
Continuity
Connector
Terminal
E101
50
Ground
Not existed
+
-
Test item
Voltage
Front combination lamp RH
Connector
Terminal
E93
4
Ground
DAYTIME
RUNNING
LIGHT
On
9 – 16 V
Off
0 – 1 V
Front combination lamp RH
Resistance
Terminal
4
6
Except 0
Ω
B1256 FRONT FOG LAMP RH POWER SUPPLY CIRCUIT
EXL-79
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
B1256 FRONT FOG LAMP RH POWER SUPPLY CIRCUIT
DTC Description
INFOID:0000000010452523
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector
• Front fog lamp RH bulb
• IPDM E/R
FAIL-SAFE
Shuts off the power supply to the front fog lamp RH power supply circuit until the front fog lamp ON conditions
are no longer satisfied.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
With CONSULT
1.
Turn ignition switch ON.
2.
Select “F FOG RH CIRC MALFUNCTN” in “Data Monitor” mode of “IPDM E/R” using CONSULT.
3.
Check the monitor status.
What is the monitor status?
“0”
>> GO TO 2.
“1”
>> A short circuit is detected multiple times in the front fog lamp RH power supply circuit, and dam-
age accumulates at the smart FET inside the IPDM E/R. For this reason, IPDM E/R does not turn
ON the smart FET. Because the DTC cannot be reproduced in this state, perform
and replace IPDM E/R after the malfunctioning part is repaired. Refer to
67, "Removal and Installation"
.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch OFF.
2.
Turn ignition switch ON.
3.
Turn lighting switch 1ST, and front fog lamp switch ON.
4.
Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
5.
Check DTC.
Is DTC detected?
YES
>> Refer to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010452524
1.
CHECK FRONT FOG LAMP RH POWER SUPPLY CIRCUIT (SHORT)
1.
Turn ignition switch OFF.
2.
Turn lighting switch OFF, and front fog lamp switch OFF.
3.
Disconnect IPDM E/R connector and front fog lamp RH connector.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
B1256
FR FOG LAMP RH PWR SPLY CIRC
(Front fog lamp right hand power supply cir-
cuit)
[CIRC
SHORT TO
GRND]
When front fog lamp ON conditions are satisfied (smart
FET inside IPDM E/R is ON), and overcurrent is detected
in the front fog lamp RH power supply circuit.
Monitor item
Monitor status
F FOG RH CIRC MALFUNCTN
0
1
EXL-80
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
B1256 FRONT FOG LAMP RH POWER SUPPLY CIRCUIT
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK FRONT FOG LAMP RH POWER SUPPLY
With CONSULT
1.
Connect IPDM E/R connector.
2.
Turn ignition switch ON
3.
Select “FRONT FOG LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.
4.
With operating the test items, check the voltage between front fog lamp RH harness connector and
ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace IPDM E/R. Refer to
PCS-67, "Removal and Installation"
3.
CHECK FRONT FOG LAMP RH BULB
Check the front fog lamp RH bulb. Refer to
EXL-80, "Component Inspection"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front fog lamp RH bulb. Refer to
Component Inspection
INFOID:0000000010452525
1.
CHECK FRONT FOG LAMP RH BULB
1.
Turn ignition switch OFF.
2.
Disconnect front fog lamp RH connector.
3.
Check resistance of front fog lamp RH terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front fog lamp RH bulb. Refer to
IPDM E/R
—
Continuity
Connector
Terminal
E101
49
Ground
Not existed
+
-
Test item
Voltage
Front fog lamp RH
Connector
Terminal
E95
1
Ground
FRONT FOG
LAMP
On
9 – 16 V
Off
0 – 1 V
Front fog lamp RH
Resistance
Terminal
1
2
Except 0
Ω
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст