Nissan Qashqai J11. Manual — part 37
OIL SEAL
EM-87
< UNIT DISASSEMBLY AND ASSEMBLY >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
OIL SEAL
FRONT OIL SEAL
FRONT OIL SEAL : Removal and Installation
INFOID:0000000010282235
REMOVAL
1.
Remove the following parts.
• Front fender protector (RH): Refer to
EXT-32, "Removal and Installation"
• Drive belt: Refer to
EM-21, "Removal and Installation"
• Crankshaft pulley: Refer to
.
2.
Position a shim (1) on the timing cover.
3.
Remove front oil seal using a flat blade screw driver (2).
NOTE:
Be careful to position the flat head of the screw driver behind the
outer lip of the crankshaft seal.
CAUTION:
Be careful not to damage front cover and crankshaft.
INSTALLATION
1.
Apply new engine oil to new front oil seal joint surface and seal lip.
2.
Install front oil seal so that each seal lip is oriented as shown in
the figure.
• Press-fit front oil seal using a suitable drift.
CAUTION:
• Be careful not to damage front cover and crankshaft.
• Press-fit oil seal straight to avoid causing burrs or tilting.
3.
Install in the reverse order of removal, for the rest of parts.
REAR OIL SEAL
REAR OIL SEAL : Removal and Installation
INFOID:0000000010282236
REMOVAL
1.
Remove transaxle assembly. Refer to
2.
Remove clutch cover and clutch disk. Refer to
CL-22, "HRA2DDT : Removal and Installation"
.
3.
Remove flywheel. Refer to
.
E1BIA1071ZZ
A
: Dust seal lip
B
: Oil seal lip
: Engine outside
: Engine inside
PBIC3485J
EM-88
< UNIT DISASSEMBLY AND ASSEMBLY >
[HRA2DDT]
OIL SEAL
4.
Remove rear oil seal with a suitable tool.
CAUTION:
Be careful not to damage crankshaft and cylinder block.
INSTALLATION
1.
Apply the liquid gasket lightly to entire outside area of new rear oil seal.
Use Genuine Liquid Gasket or equivalent.
2.
Install rear oil seal so that each seal lip is oriented as shown in
the figure.
• Press-fit rear oil seal with a suitable drift (A).
CAUTION:
• Be careful not to damage crankshaft and cylinder block.
• Press-fit oil seal straight to avoid causing burrs or tilt-
ing.
• Never touch grease applied onto oil seal lip.
• Press in rear oil seal (1) to the position as shown in the figure.
3.
Install in the reverse order of removal, for the rest of parts.
E1BIA1076ZZ
A
: Dust seal lip
B
: Oil seal lip
: Engine outside
: Engine inside
PBIC3485J
PBIC3660E
A
: Rear end surface of cylinder block
b
: 0 - 0.5 mm (0 - 0.020 in)
PBIC3149J
OIL PAN (UPPER)
EM-89
< UNIT DISASSEMBLY AND ASSEMBLY >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
OIL PAN (UPPER)
Exploded View
INFOID:0000000010282247
Removal and Installation
INFOID:0000000010282248
REMOVAL
1.
Separate engine from gearbox.
2.
Remove clutch disk and clutch cover. Refer to
CL-22, "HRA2DDT : Exploded View"
.
1.
Baffle plate
2.
Dowel pin
3.
Oil pan (upper)
4.
Oil pump release valve
5.
Oil filter
6.
O-ring
7.
Oil level sensor
8.
Oil filter cover
9.
Metal clip
10. Oil pump solenoide valve
11.
Oil pump solenoide valve O-ring
12. Drain plug washer
13. Oil pan lower
14. Oil pump strainer
15. Oil pump strainer O-ring
16. Oil pump bracket
17. Oil pump
A.
B.
Refer to
E1BIA1045GB
EM-90
< UNIT DISASSEMBLY AND ASSEMBLY >
[HRA2DDT]
OIL PAN (UPPER)
3.
Remove flywheel. Refer to
.
4.
Remove oil filter. Refer to
LU-10, "Removal and Installation"
5.
Remove the timing chain. Refer to
.
6.
Remove the oil level sensor. Refer to
7.
Remove the oil pan (lower). Refer to
8.
Remove the oil pump. Refer to
.
9.
Remove oil cooler. Refer to
10. Remove oil pan (upper) with the following procedure.
a.
Loosen oil pan (upper) mounting bolts in the reverse of the order as shown in the figure.
CAUTION:
Take care to note the place and length of each bolt
removed.
b.
Insert a flat-bladed screwdriver (1) and open up a crack between the oil pan (upper) cylinder block.
CAUTION:
• Be careful not to damage the mating surface.
: Engine front
E1BIA1101ZZ
E1BIA1046ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст