Nissan Qashqai J11. Manual — part 1435
DIAGNOSIS SYSTEM (BCM)
SEC-39
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
KEY SW
NOTE:
This item is displayed, but cannot be monitored
IGN SW
NOTE:
This item is displayed, but cannot be monitored
START SW
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Buzzer 1: Combination meter buzzer sounds (pipipi...) when CONSULT screen is touched
• Buzzer 2: Combination meter buzzer sounds (pipi-pipi-...) when CONSULT screen is
touched
• Buzzer 3: Combination meter buzzer sounds (pipipipi-pipipipi-...) when CONSULT screen is
touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON:[ Intelligent key system malfunction] displays when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched
HORN
This test is able to check horn operation
• On: Operates
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR +5
NOTE:
This item is displayed, but cannot be used
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched
PUSH SWITCH INDICATOR
This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched
ENGINE START REQUEST
This test is able to check BCM sends starter request signal to IPDM E/R via CAN communi-
cation
• MODE 1: IGN ON, START request OFF
• MODE 2: IGN OFF, START request ON
• MODE 3: IGN ON, START request ON
• Off: Non-operation
IGNITION RELAY
NOTE:
This item is displayed, but cannot be used
STARTER CUT RELAY
This test is able to operate the starter control relay
• On: Operates
• Off: Non-operation
ENGINE START
NOTE:
This item is displayed, but cannot be used
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is displayed, but cannot be used
SEC-40
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
MULTI REMOTE ENT
MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT) (Type 3)
INFOID:0000000010827933
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
REVERSE LAMP TEST
NOTE:
This item is displayed, but cannot be used
KEYFOB P/W TEST
NOTE:
This item is displayed, but cannot be used
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be used
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk room lamp operation
• On: Operates
• Off: Non-operation
Test item
Description
Test item
Description
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec.
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
ANSWER BACK
NOTE:
This item is displayed, but cannot be used
ANSWER BACK KEYLESS
LOCK UNLOCK
NOTE:
This item is displayed, but cannot be used
WELCOME LIGHT OP SET
NOTE:
This item is displayed, but cannot be used
Monitor Item
Condition
CONFRM ID ALL
Indicates [Yet] at all time.Switches to [Done] when a registered key is inserted into ignition key
cylinder.
CONFRM ID4
CONFRM ID3
CONFRM ID2
CONFRM ID1
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received. Indicates [ID
NG] when key ID that is not registered is received.
DIAGNOSIS SYSTEM (BCM)
SEC-41
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
CLUTCH SW*
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from keyfob
KEY SW
Indicates [On/Off] condition of key switch
IGN SW
Indicates [On/Off] condition of ignition switch in ON position
START SW
Indicates [On/Off] condition of ignition switch in START position
Monitor Item
Condition
Test item
Description
FLASHER
This test is able to check flasher operation [LH/RH/Off]
HORN
NOTE:
This item is indicated, but not monitored
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR+5
NOTE:
This item is indicated, but not monitored
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is indicated, but not monitored
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
SEC-42
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT) (Type 4)
INFOID:0000000010827934
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk/luggage room lamp operation
• On: Operates
• Off: Non-operation
Test item
Description
Test item
Description
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec.
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
ANSWER BACK
NOTE:
This item is displayed, but cannot be used
ANSWER BACK KEYLESS
LOCK UNLOCK
NOTE:
This item is displayed, but cannot be used
WELCOME LIGHT OP SET
NOTE:
This item is displayed, but cannot be used
Monitor Item
Condition
CONFRM ID ALL
Indicates [Yet] at all time.Switches to [Done] when a registered key is inserted into ignition key
cylinder.
CONFRM ID4
CONFRM ID3
CONFRM ID2
CONFRM ID1
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received. Indicates [ID
NG] when key ID that is not registered is received.
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
CLUTCH SW*
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст