Nissan Qashqai J11. Manual — part 1661
DIAGNOSIS SYSTEM (BCM)
MIR-19
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Buzzer 1: Combination meter buzzer sounds (pipipi...) when CONSULT screen is touched
• Buzzer 2: Combination meter buzzer sounds (pipi-pipi-...) when CONSULT screen is
touched
• Buzzer 3: Combination meter buzzer sounds (pipipipi-pipipipi-...) when CONSULT screen is
touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON:[ Intelligent key system malfunction] displays when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched
HORN
NOTE:
This item is displayed, but cannot be used
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR +5
NOTE:
This item is displayed, but cannot be used
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched
PUSH SWITCH INDICATOR
This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched
ENGINE START REQUEST
This test is able to check BCM sends starter request signal to IPDM E/R via CAN communi-
cation
• MODE 1: IGN ON, START request OFF
• MODE 2: IGN OFF, START request ON
• MODE 3: IGN ON, START request ON
• Off: Non-operation
IGNITION RELAY
NOTE:
This item is displayed, but cannot be used
STARTER CUT RELAY
This test is able to operate the starter control relay
• On: Operates
• Off: Non-operation
ENGINE START
NOTE:
This item is displayed, but cannot be used
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is displayed, but cannot be used
REVERSE LAMP TEST
NOTE:
This item is displayed, but cannot be used
KEYFOB P/W TEST
NOTE:
This item is displayed, but cannot be used
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be used
MIR-20
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH/
CHANGEOVER SWITCH)
DTC/CIRCUIT DIAGNOSIS
DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH/
CHANGEOVER SWITCH)
Component Inspection
INFOID:0000000010339493
1.
CHECK MIRROR SWITCH & CHANGEOVER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check door mirror remote control switch.
[LHD models]
Door mirror remote control switch
Condition
Continuity
Terminal
Changeover
switch
Mirror switch
Driver side
15
12
LEFT
RIGHT
Existed
10
1
15
1
LEFT
10
12
15
4
UP
10
12
15
12
DOWN
10
4
Passenger side
15
11
RIGHT
RIGHT
10
9
15
9
LEFT
10
11
15
3
UP
10
11
15
11
DOWN
10
3
DIAGNOSIS SYSTEM (BCM)
MIR-21
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW*
1
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
NEUTRAL SW - IPDM
Indicates [On/Off] condition of park/neutral position switch
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
STARTER RELAY - IPDM
Indicates [On/Off] condition of starter relay
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
ST/INHIRELAY-IPDM
Display the starter relay/starter control relay status signal from IPDM E/R via CAN communica-
tion
REVERSE SIGNAL - IPDM
Indicates [On/Off] condition of R position
CRANKING PERMIT - ECM
Display the engine cranking permit signal from ECM via CAN communication
IS STATUS - ECM
Indicates [On/Off] condition of stop/start system
STARTER CUT RELAY - ECM
Indicates [On/Off] condition of starter control relay signal from ECM via CAN communication
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
IGN REQ - IPDM
Display the ignition request signal from IPDM E/R via CAN communication
STARTER REQ - IPDM
Display the starter request signal from IPDM E/R via CAN communication
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
ID OK FLAG
Indicates [Set/Reset] condition of Intelligent Key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possible
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
I-KEY OK FLAG
Indicates [KEY On/NOT On] condition of Intelligent Key ID and Intelligent Key is detected inside
vehicle
PRBT ENG STRT
Indicates whether or not the engine is in start prohibited status
ID AUTHENT CANCEL TIMER
Indicates whether or not it is in engine start possible status when Intelligent Key verification is
unnecessary
ACC BATTERY SAVER
Indicates [On/Off] whether or not ignition battery saver is in operation
CRNK PRBT TMR
Indicates [On/Off] whether or not in cranking prohibited status due to starter motor protection
function operation
AUT CRANK TMR
Indicates [On/Off] whether or not in AUTO CRANKING MODE status
CRNK PRBT TME
Indicates the time for changing from cranking prohibited status to cranking possible status
MIR-22
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH (OPEN/CLOSE SWITCH)
DOOR MIRROR REMOTE CONTROL SWITCH (OPEN/CLOSE SWITCH)
Component Inspection
INFOID:0000000010339494
1.
CHECK OPEN/CLOSE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check door mirror remote control switch.
[LHD models]
[RHD models]
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch. Refer to
MIR-33, "Removal and Installation"
Door mirror remote control switch
Condition
Continuity
Terminal
Driver side
15
6
Open/close switch
OPEN
Existed
10
8
15
8
CLOSE
10
6
Passenger side
15
5
OPEN
10
7
15
7
CLOSE
10
5
Door mirror remote control switch
Condition
Continuity
Terminal
Driver side
15
5
Open/close switch
OPEN
Existed
10
7
15
7
CLOSE
10
5
Passenger side
15
6
OPEN
10
8
15
8
CLOSE
10
6
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст