Nissan Qashqai J11. Manual — part 618
TRANSAXLE ASSEMBLY
TM-47
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
24. Remove selector lever oil seal and bushings from transaxle
case using a suitable remover.
25. Remove oil gutter (1) from transaxle case.
26. Remove shifter lever oil seal (1) from transaxle case.
27. Remove bushings (1) from transaxle case using a suitable
remover.
28. Remove mainshaft rear bearing outer race from transaxle case
using a suitable remover and then remove bearing preloading
shim.
CAUTION:
Never damage transaxle case.
PCIB1713E
PCIB1707E
PCIB1709E
PCIB1710E
PCIB1706E
TM-48
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
29. Remove snap ring (1) and oil channel (2) from transaxle case.
30. Remove input shaft oil seal (1) from clutch housing using a flat-
bladed screwdriver.
31. Remove mainshaft front bearing outer race (1) and oil channel
(2) from clutch housing using the puller (A) [SST: KV381054S0]
and the spacer (B) [Commercial service tool].
32. Remove bushings (1) from clutch housing using a suitable
remover.
33. Remove two way connector (1) from clutch housing.
34. Remove plug. (If equipped)
PCIB1708E
PCIB1714E
JPDIC0107ZZ
PCIB1717E
PCIB1720E
TRANSAXLE ASSEMBLY
TM-49
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
35. Remove pinion gear (1) and pinion shaft (2) from clutch housing.
(If equipped)
Assembly
INFOID:0000000010288459
1.
Install pinion gear (1) and pinion shaft (2) into clutch housing. (If
equipped)
2.
Install plug. (If equipped)
3.
Install two way connector (1) into clutch housing.
4.
Install bushings (1) until they are flush with end face of clutch
housing using the drift (A) [Commercial service tool].
PCIB1719E
PCIB1719E
PCIB1720E
JPDIC0108ZZ
TM-50
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
5.
Install oil channel and mainshaft front bearing outer race into
clutch housing using the drift (A) [SST: KV38100200].
CAUTION:
• Never reuse oil channel.
• Replace mainshaft front bearing outer race and mainshaft
front bearing inner race as a set.
6.
Install input shaft oil seal (1) into clutch housing using the drift
(A) [SST: ST33220000].
7.
Install snap ring (1) and oil channel (2) onto transaxle case.
8.
Install bearing preloading shim and mainshaft rear bearing outer
race into transaxle case using the drift (A) [SST: KV38100200].
CAUTION:
Replace mainshaft rear bearing outer race and mainshaft
rear bearing inner race as a set.
9.
Install bushings (1) into transaxle case using the drift (A) [Com-
mercial service tool].
PCIB1724E
PCIB1721E
PCIB1729E
PCIB1728E
JPDIC0109ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст