Nissan Qashqai J11. Manual — part 2270
CHASSIS MAINTENANCE
MA-115
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
Unit: mm (in)
EXHAUST SYSTEM
EXHAUST SYSTEM : Inspection
INFOID:0000000010355390
Check exhaust pipes, muffler, and mounting for improper attach-
ment, leakage, cracks, damage or deterioration.
• If anything is found, repair or replace damaged parts.
CVT FLUID (RE0F10G)
CVT FLUID (RE0F10G) : Inspection
INFOID:0000000010508834
FLUID LEAKAGE
Vertical center line of headlamp H.
Horizontal center line of headlamp
L.
Distance from headlamp center to screen
X.
Aiming adjustment area
(Lateral)
Y.
Aiming adjustment area
(Vertical)
Distance from headlamp center to screen (L)
: 10 m (32.8 ft)
Aiming adjustment area
Vertical direction (Y)
(Lower side from headlamp center height)
Lateral direction (X)
(Right side from headlamp center line)
Highest light axis
100 (3.94)
0 - 100 (3.94)
Target light axis
100 (3.94)
Lowest light axis
130 (5.12)
JSLIA0031ZZ
SMA211A
MA-116
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE (K9K)
ENGINE OIL : Draining
INFOID:0000000011497401
WARNING:
• Be careful not to burn yourself, as the engine oil is hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer: try to avoid direct skin
contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as
possible.
1.
Put vehicle horizontally.
2.
Warm up engine, and check for oil leakage from engine components.
3.
Stop engine and wait for 10 minutes.
4.
Loosen oil filler cap.
5.
Remove drain plug and then drain engine oil.
ENGINE OIL : Refilling
INFOID:0000000011497402
1.
Refill with new engine oil.
• Refer to
MA-64, "Fluids and Lubricants"
.
• The refill capacity depends on the oil temperature and drain time.
Use these specifications for reference only.
Always use the dipstick to the determine when the proper amount
of oil is in the engine.
CAUTION:
• Be sure to clean drain plug and install with new washer.
• The refill capacity depends on the oil temperature and drain time. Use these specifications for ref-
erence only.
Always use the dipstick to the determine when the proper amount of oil is in the engine.
2.
Warm up engine and check area around drain plug and oil filter for oil leakage.
3.
Stop engine and wait for 10 minutes.
4.
Check oil level.
OIL FILTER
OIL FILTER : Replacement
INFOID:0000000011497404
1.
Using an oil filter wrench [SST: KV113C0010 (Mot. 1329)],
remove oil filter.
CAUTION:
• Be careful not to get burned when the engine and engine
oil are hot.
• When removing, prepare a shop cloth to absorb any oil
leakage or spillage.
• Do not allow engine oil to adhere to the drive belts.
• Completely wipe off any oil that adhere to the engine and
the vehicle.
2.
Remove foreign materials adhering to the oil filter installation
surface.
3.
Install oil filter bracket to oil cooler.
CAUTION:
Install oil filter bracket, positioning lug in the hole of oil cooler.
Oil capacity (Approximate)
: Refer to
"Periodical Maintenance Specification"
.
MBIB0548E
MBIB0551E
ENGINE MAINTENANCE (K9K)
MA-117
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
4.
Apply engine oil to the oil seal contact surface of the new oil fil-
ter.
5.
Install the oil filter until it comes into contact with the oil seal on
the engine bracket.
6.
Using an oil filter wrench [SST: KV113C0010 (Mot. 1329)],
tighten oil filter.
7.
After warming up the engine, check for engine oil leakage.
8.
Check oil level and add engine oil. Refer to
OIL FILTER : Inspection
INFOID:0000000011497405
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
MA-115, "ENGINE OIL : Inspection"
2.
Start the engine, and check there is no leak of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
MA-115, "ENGINE OIL : Inspection"
.
: 14 N·m (1.4 kg-m, 10 ft-lb)
SMA010
MA-118
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
1.
Check that the selector lever is in the “P” position, then completely engage the parking brake.
2.
Start the engine.
3.
Adjust the CVT fluid temperature to be approximately 40
°
C (104
°
F).
NOTE:
The CVT fluid is largely affected by temperature. Therefore be sure to use CONSULT and check the
“FLUID TEMP” under “TRANSMISSION” in “Data Monitor” while adjusting.
4.
While depressing the brake pedal, shift the selector lever to the entire position from “P” to “D”, and shift it
to the “P” position.
NOTE:
Hold the lever at each position for 5 seconds.
5.
Lift up the vehicle.
6.
Check that there is no CVT fluid leakage.
7.
Remove the overflow plug
from converter housing.
8.
Install the charging pipe set (KV311039S0) (A) into the overflow
plug hole.
CAUTION:
Tighten the charging pipe by hand.
9.
Install the ATF changer hose (B) to the charging pipe.
CAUTION:
Press the ATF changer hose all the way onto the charging
pipe until it stops.
10. Fill approximately 0.5 liter (1/2 lmp qt) of the CVT fluid.
11. Remove the ATF changer hose from the charging pipe, and
check that the CVT fluid drains out from the charging pipe. If it
does not drain out, perform charging again.
CAUTION:
Perform this work with the vehicle idling.
12. When the flow of CVT fluid slows to a drip, remove the charging pipe from the converter housing.
13. Tighten the overflow plug to the specified torque. Refer to
.
CAUTION:
Never reuse O-ring.
14. Lift down the vehicle.
15. Stop the engine.
CVT FLUID (RE0F10D)
CVT FLUID (RE0F10D) : Inspection
INFOID:0000000010735721
FLUID LEAKAGE
: Vehicle front
JSDIA3714ZZ
JSDIA3713ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст