Nissan Qashqai J11. Manual — part 33
CYLINDER HEAD
EM-71
< UNIT DISASSEMBLY AND ASSEMBLY >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
4.
Remove cylinder head loosening bolts in reverse order as
shown in the figure with cylinder head wrench (commercial ser-
vice tool).
5.
Remove cylinder head gasket.
INSTALLATION
1.
Install new cylinder head gasket.
2.
Tighten cylinder head bolts in numerical order as shown in the
figure with the following procedure to install cylinder head.
CAUTION:
Cylinder head bolts can not be reuse.
a.
Apply new engine oil to threads and seating surfaces of mount-
ing bolts.
b.
Tighten all bolts.
c.
Turn all bolts 270 degrees clockwise (angle tightening).
CAUTION:
Check and confirm the tightening angle by using the angle
wrench [SST: KV10112100] (A) or protractor. Avoid judg-
ment by visual inspection without the tool.
3.
Install in the reverse order of removal after this step.
Disassembly and Assembly
INFOID:0000000010282239
DISASSEMBLY
1.
Remove spark plug with a spark plug wrench (commercial service tool).
2.
Remove valve lifter.
• Identify installation positions, and store them without mixing them up.
3.
Remove valve collet.
A
: INT side
B
: EXH side
: Engine front
E1BIA1042ZZ
A
: INT side
B
: EXH side
: Engine front
: 25.0 N·m (2.6 kg-m, 18 ft-lb)
E1BIA1042ZZ
PBIC3733E
EM-72
< UNIT DISASSEMBLY AND ASSEMBLY >
[HRA2DDT]
CYLINDER HEAD
• Compress valve spring with the valve spring compressor
(commercial service tool).
• Remove valve collet with a magnet hand.
CAUTION:
When working, be careful not to damage valve lifter holes.
4.
Remove valve spring retainer and valve spring.
5.
Measure position "H" of one of the valve oil seal with the follow-
ing procedure.
CAUTION:
Before removing the valves and the valve oil seals, it is vital
to measure position "H" of one of the valve oil seal in rela-
tion with the cylinder head using [SST: KV113B0330 (Mot.
1511)] or equivalent tool.
a.
Install the push rod (A) of [SST: KV113B0330 (Mot. 1511)] or
equivalent tool on the valve oil seal.
NOTE:
The inner diameter of the push rod must be identical to that of
the valve. In addition, the bottom of the push rod must come into
contact with the metal upper section of the valve oil seal.
b.
Install the guide tube (B) over the push rod until the guide tube
comes into contact with the cylinder head, locking the push rod
with the knurled wheel.
c.
Remove the guide tube assembly and push rod, being careful
not to loosen the knurled wheel.
d.
Push valve stem to combustion chamber side, and remove
valve.
• Identify installation positions, and store them without mixing
them up.
e.
Remove using [SST: KV113B0090 (Mot. 1335)] or equivalent
valve oil seals.
6.
7.
Remove valve spring seat.
ASSEMBLY
1.
Check valve seat contact. Refer to
2.
Install valve.
E1BIA1100ZZ
MBIB0417E
MBIB0418E
MBIB0419E
CYLINDER HEAD
EM-73
< UNIT DISASSEMBLY AND ASSEMBLY >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Lubricate the inside of the valve guide.
3.
Instal valve oil seal with the following procedure.
a.
Install the barrel of [SST: KV113B0330 (Mot. 1511)] or equiva-
lent tool on the valve stem.
NOTE:
The inner diameter of the barrel must be identical to the diame-
ter of the valve stem.
b.
Keep the valve pressed in contact with the valve seat
c.
Install the valve oil seal on the barel of [SST: KV113B0330 (Mot.
1511)] or equivalent.
NOTE:
Never lubricate the valve oil seal before install them.
d.
Push the valve oi seal until it past the barrel of [SST:
KV113B0330 (Mot. 1511)] or equivalent then remove the barrel
of [SST: KV113B0330 (Mot. 1511)] or equivalent.
MBIB0421E
MBIB0422E
MBIB0423E
MBIB0424E
EM-74
< UNIT DISASSEMBLY AND ASSEMBLY >
[HRA2DDT]
CYLINDER HEAD
e.
Install guide tube and push rod of [SST: KV113B0330 (Mot.
1511)] or equivalent on the valve oil seal.
f.
Push the valve oil seal by tapping by hand on the sleeve of [SST:
KV113B0330 (Mot. 1511)] or equivalent until guide tube reaches
the cylinder head.
4.
Repeat the operations for all the valves.
5.
Install valve spring seat.
6.
Install valve spring and valve spring retainer.
7.
Install valve collet.
• Compress valve spring with the valve spring compressor.
valve (commercial service tool).
• Install valve collet with a magnet hand.
CAUTION:
When working, be careful not to damage valve lifter holes.
• Tap valve stem edge lightly with a plastic hammer after instal-
lation to check its installed condition.
8.
Install valve lifter.
9.
Install spark plug with a spark plug wrench (commercial service
tool).
Inspection
INFOID:0000000010365193
INSPECTION AFTER REMOVAL
Cylinder Head Distortion
NOTE:
When performing this inspection, cylinder block distortion should be also checking. Refer to
.
1.
Wipe off engine oil and remove water scale (like deposit), gasket, sealant, carbon, etc. with a scraper.
CAUTION:
Use utmost care not to allow gasket debris to enter passages for engine oil or engine coolant.
MBIB0425E
E1BIA1100ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст