Nissan Qashqai J11. Manual — part 1407
HAZARD FUNCTION
DLK-897
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HAZARD FUNCTION
Component Function Check
INFOID:0000000010672520
1.
CHECK FUNCTION
1.
Select “MULTI REMOTE ENT” of “BCM” using CONSULT.
2.
Select “FLASHER” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Hazard warning lamp circuit is OK.
NO
>> Refer to
DLK-897, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010672521
1.
CHECK HAZARD OPERATION
EXL-195, "TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Description"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Monitor item
Status
FLASHER
LH
Front turn signal lamp LH
Turns ON
RH
Front turn signal lamp RH
Turns ON
OFF
Front turn signal lamp
Turns OFF
DLK-898
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 6]
KEY SWITCH
KEY SWITCH
Component Function Check
INFOID:0000000010672522
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “KEY SW” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Key switch is OK.
NO
>> Refer to
DLK-898, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010672523
1.
CHECK KEY SWITCH POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect key switch connector.
3.
Check voltage between key switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK KEY SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between key switch harness connector and BCM harness connector.
3.
Check continuity between key switch connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Check continuity between key switch connector and ground.
Monitor item
Condition
Status
KEY SW
Keyfob
Inserted in key cylinder
ON
Removed from key cylinder
OFF
Key switch
Ground
Voltage
Connector
Terminal
M47
1
9 – 16 V
Key switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
M47
1
M69
81
Existed
Key switch
Ground
Continuity
Connector
Terminal
M47
1
Not existed
Key switch
Ground
Continuity
Connector
Terminal
M47
2
Existed
KEY SWITCH
DLK-899
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace ignition key cylinder.
NO
>> Repair or replace the malfunctioning parts.
DLK-900
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 6]
KEYFOB BATTERY
KEYFOB BATTERY
Component Inspection
INFOID:0000000010672524
1.
CHECK KEYFOB BATTERY
Check by connecting a resistance (approximately 300
Ω
) so that the
current value becomes about 10 mA.
Is the measurement value within the specification?
YES
>> INSPECTION END
NO
>> Replace keyfob battery. Refer to
.
Standard
: Approx. 2.5 - 3.0 V
OCC0607D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст