Nissan Qashqai J11. Manual — part 1009
SR-14
< REMOVAL AND INSTALLATION >
DRIVER AIR BAG MODULE
REMOVAL AND INSTALLATION
DRIVER AIR BAG MODULE
Exploded View
INFOID:0000000010478317
Removal and Installation
INFOID:0000000010478318
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Always work from the side of driver air bag module. Never work in front of it.
• Never use the air tools or electric tools for servicing.
REMOVAL
1.
Release driver air bag module hooks.
a.
Locate the access hole on RH side of steering wheel rear fin-
isher (1) and insert a 5.0 mm (0.20 in) diameter suitable tool (A).
b.
Push suitable tool (A) inward and make sure the tool contacts
the spring (2) as shown. Push on the upper right of the driver air
bag module while pressing on the spring to release the driver air
bag module hook (RH). Repeat procedure for driver air bag
module hook (LH).
1.
Steering wheel
2.
Driver air bag module
ALHIA0342ZZ
AWHIA0361ZZ
DRIVER AIR BAG MODULE
SR-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
2.
Pull out the driver air bag module assembly as shown.
3.
Disconnect the driver air bag module harness connector.
CAUTION:
• For installing/removing the driver air bag module harness
connector, insert thin screwdriver wrapped in tape into
notch, lift lock and remove the connector.
• Install the connector with lock raised, and push lock into
the connector.
• After installing the connector, check that the lock is
pushed securely into it.
4.
Remove the driver air bag module.
CAUTION:
• Always place the driver air bag module with pad side fac-
ing upward.
: Upward
• Never impact the driver air bag module.
• Replace the driver air bag module if it has been dropped
or sustained an impact.
• Never insert any foreign objects (screwdriver, etc.) into the driver air bag module.
• Never disassemble the driver air bag module.
• Never expose the driver air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the driver air bag module.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Never damage the harness while installing.
AWHIA0632ZZ
PHIA0953J
AWHIA0633ZZ
JMHIA0009ZZ
SR-16
< REMOVAL AND INSTALLATION >
DRIVER AIR BAG MODULE
• Tighten the TORX bolts after completely adjusting the centers of fixing bolts on the driver air bag
module side and the steering wheel side. If the holes are misaligned, the bolt threads are damaged
and the module is not installed securely.
• If malfunction is detected by the air bag warning lamp after repair or replacement of the malfunction-
ing parts, reset the memory using self-diagnosis or CONSULT. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
SPIRAL CABLE
SR-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SPIRAL CABLE
Exploded View
INFOID:0000000010478319
Removal and Installation
INFOID:0000000010478320
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
REMOVAL
1.
Remove the steering wheel. Refer to
ST-8, "Removal and Installation"
2.
Remove the steering column upper and lower cover. Refer to
.
3.
Disconnect harness connectors (A).
4.
Remove screws (A) and then remove spiral cable (1).
CAUTION:
ALHIA0359ZZ
1.
Combination switch
2.
Steering angle sensor
3.
Spiral cable
ALHIA0351ZZ
ALHIA0350ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст