Nissan Qashqai J11. Manual — part 338
P1564 ASCD STEERING SWITCH
ECM-329
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
ECM
N
P
O
2.
Also check harness for short to ground and to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning part.
5.
CHECK ASCD STEERING SWITCH
Check ASCD steering switch. Refer to
ECM-329, "Component Inspection"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace ASCD steering switch. Refer to
ST-8, "Removal and Installation"
Component Inspection
INFOID:0000000010703022
1.
CHECK ASCD STEERING SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect combination switch (spiral cable) harness connector.
3.
Check the resistance between combination switch harness connector terminals as per the following condi-
tions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace ASCD steering switch. Refer to
ST-8, "Removal and Installation"
+
–
Continuity
Combination switch
(Spiral cable)
ECM
Connector
Terminal
Connector
Terminal
M66
27
E57
110
Existed
Combination switch
(Spiral cable)
Condition
Resistance
(Approx.)
Connector
+
−
Terminal
M303
8
9
MAIN switch: Pressed
0
Ω
CANCEL switch: Pressed
250
Ω
COAST/SET switch: Pressed
660
Ω
ACCEL/RES switch: Pressed
1,480
Ω
All ASCD steering switches: Released
4,000
Ω
ECM-330
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
P1568 SIGNAL INVALID
P1568 SIGNAL INVALID
DTC Description
INFOID:0000000010703023
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis control module
• ECM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.
CHECK DTC PRIORITY
If DTC P1568 is displayed with DTC UXXXX, first perform the confirmation procedure for DTC UXXXX.
Is applicable DTC detected?
YES
>> Perform diagnosis for detected DTC. Refer to
.
NO
>> GO TO 2.
2.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 5 seconds.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
ECM-330, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010703024
1.
CHECK DTC PRIORITY
If DTC P1568 is displayed with DTC UXXXX, first perform the confirmation procedure for DTC UXXXX.
Is applicable DTC detected?
YES
>> Perform diagnosis for detected DTC. Refer to
.
NO
>> GO TO 2.
2.
CHECK SELF-DIAGNOSTIC RESULT OF CHASSIS CONTROL MODULE
Check that the chassis control module does not detect any DTC.
Is any DTC detected?
YES
>> GO TO 3.
NO
>> Replace chassis control module. Refer to
DAS-312, "Removal and Installation"
.
3.
REPLACE CHASSIS CONTROL MODULE
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P1568
ICC COMMAND VALUE
(Intelligent cruise control command value)
ECM detects that a throttle valve opening angle request signal sent from
chassis control module is difference from the specified value calculated by
ECM.
P1568 SIGNAL INVALID
ECM-331
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
ECM
N
P
O
1.
Replace chassis control module. Refer to
DAS-312, "Removal and Installation"
2.
Perform DTC Confirmation Procedure again.
Is DTC P1568 detected again?
YES
>> Replace ECM. Refer to
ECM-416, "Removal and Installation"
NO
>> INSPECTION END
ECM-332
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
P1572 BRAKE PEDAL POSITION SWITCH
P1572 BRAKE PEDAL POSITION SWITCH
DTC Description
INFOID:0000000010703025
DTC DETECTION LOGIC
NOTE:
This self-diagnosis has the one trip detection logic. When malfunction A is detected, DTC is not stored in ECM
memory. And in that case, 1st trip DTC and 1st trip freeze frame data are displayed. 1st trip DTC is erased
when ignition switch OFF. And even when malfunction A is detected in two consecutive trips, DTC is not
stored in ECM memory.
POSSIBLE CAUSE
• Harness or connectors
- Stop lamp switch circuit is shorted.
- Brake pedal position switch circuit is shorted.
• Stop lamp switch
• Brake pedal position switch
• Incorrect stop lamp switch installation
• Incorrect brake pedal position switch installation
• ECM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.
CHECK DTC PRIORITY
If DTC P1572 is displayed with DTC P0605, perform the trouble diagnosis for DTC P0605.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. Refer to
NO
>> GO TO 2.
2.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
NOTE:
Procedure for malfunction B is not described here. It takes extremely long time to complete procedure for mal-
function B. By performing procedure for malfunction A, the incident that causes malfunction B can be
detected.
Will CONSULT be used?
YES
>> GO TO 3.
NO
>> GO TO 5.
3.
PERFORM DTC CONFIRMATION PROCEDURE-1
With CONSULT
1.
Start engine.
2.
Select “DATA MONITOR” mode of “ENGINE” using CONSULT.
3.
Press MAIN switch and make sure that CRUISE indicator is displayed in combination meter.
4.
Drive the vehicle for at least 5 consecutive seconds as per the following conditions.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P1572
ASCD BRAKE SW
(ASCD brake switch)
A
When the vehicle speed is above 30 km/h (19 MPH), ON signals from the
stop lamp switch and the brake pedal position switch are sent to the ECM
at the same time.
B
Brake pedal position switch signal is not sent to ECM for extremely long
time while the vehicle is driving.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст