Nissan Qashqai J11. Manual — part 51
AIR CLEANER FILTER
EM-143
< PERIODIC MAINTENANCE >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
MAINTENANCE INTERVAL
MA-22, "MR20DD : Periodic Maintenance"
.
Inspection (Viscous Paper Type)
INFOID:0000000010715462
INSPECTION AFTER REMOVAL
Examine with eyes that there is no stain, clogging, or damage on air cleaner element.
• Remove dusts (such as dead leafs) on air cleaner element surface and inside cleaner case.
• If clogging or damage is observed, replace the air cleaner element.
CAUTION:
Never clean the viscous paper type air cleaner element by blowing as there is a risk of deterioration of
its performance
MAINTENANCE INTERVAL
MA-22, "MR20DD : Periodic Maintenance"
.
EM-144
< PERIODIC MAINTENANCE >
[MR20DD]
SPARK PLUG
SPARK PLUG
Exploded View
INFOID:0000000010715463
Removal and Installation
INFOID:0000000010715464
REMOVAL
1.
Remove resonater of air duct assembly. Refer to
.
2.
Remove ignition coil. Refer to
Ignition coil
Spark plug
Rocker cover
Rocker cover gasket
Oil filler cap
PCV valve
O-ring
Comply with the installation proce-
dure when tightening. Refer to
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JPBIA6815GB
SPARK PLUG
EM-145
< PERIODIC MAINTENANCE >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
3.
Remove spark plug with a spark plug wrench (commercial ser-
vice tool).
CAUTION:
Never drop or shock spark plug.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000010715465
INSPECTION AFTER REMOVAL
Use the standard type spark plug for normal condition.
CAUTION:
• Never drop or shock spark plug.
• Never use a wire brush for cleaning.
• If plug tip is covered with carbon, spark plug cleaner may be
used.
• Checking and adjusting plug gap is not required between
replacement intervals.
• Measure spark plug gap. when it exceeds the limit, replace
spark plug even if it is with in the specified replacement mile-
age. Refer to
.
: 14 mm (0.55 in)
JPBIA0030ZZ
Spark plug (Standard type)
: Refer to
.
Cleaner air pressure
: Less than 588 kPa (5.88 bar, 6
kg/cm
2
, 85 psi)
Cleaning time
: Less than 20 seconds
SMA773C
JPBIA0031ZZ
EM-146
< REMOVAL AND INSTALLATION >
[MR20DD]
DRIVE BELT AUTO-TENSIONER
REMOVAL AND INSTALLATION
DRIVE BELT AUTO-TENSIONER
Exploded View
INFOID:0000000010715468
Removal and Installation
INFOID:0000000010715469
Removal
1.
Remove drive belt. Refer to
EM-139, "Removal and Installation"
• Keep each auto-tensioner pulley arm locked after drive belts are removed.
2.
Support the bottom surface of engine using a transmission jack, and then remove the rear torque rod and
the engine mounting insulator (RH). Refer to
CAUTION:
When using the jack, apply a piece of wood to the oil pan (lower) mounting bolt to protect the bot-
tom of engine from being scratched.
3.
Remove drive belt auto-tensioner mounting bolt
from service
hole
of right side member
.
NOTE:
Lift the front side of engine with a jack supporting the bottom of
engine and align drive belt auto-tensioner mounting bolt position
with the service hole.
4.
Remove drive belt auto-tensioner.
Installation
Install in the reverse order of removal.
CAUTION:
When installing drive belt auto-tensioner, be careful not to interfere with water pump pulley.
Front cover
Drive belt auto-tensioner
: N·m (kg-m, ft-lb)
JPBIA4304GB
: Drive belt auto-tensioner
: Vehicle front
PBIC3138J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст