Nissan Qashqai J11. Manual — part 1375
P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OPER-
ATE
DLK-769
< SYMPTOM DIAGNOSIS >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OP-
ERATE
Diagnosis Procedure
INFOID:0000000010683779
1.
CHECK “AUTO LOCK FUNCTION” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “AUTO LOCK FUNCTION” in “WORK SUPPORT” mode.
3.
Check “AUTO LOCK FUNCTION” in “WORK SUPPORT”.
Refer to
DLK-675, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (Type 5)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “MODE 2” in “AUTO LOCK FUNCTION”.
2.
CHECK “AUTO UNLOCK FUNCTION” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “AUTO UNLOCK FUNCTION” in “WORK SUPPORT” mode.
3.
Check “AUTO UNLOCK FUNCTION” in “WORK SUPPORT”.
Refer to
DLK-675, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (Type 5)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “MODE 2” in “AUTO UNLOCK FUNCTION”.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
DLK-770
< SYMPTOM DIAGNOSIS >
[TYPE 5]
P POSITION WARNING DOES NOT OPERATE
P POSITION WARNING DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000010672399
1.
CHECK DTC WITH BCM, TCM AND COMBINATION METER
Check that DTC is not detected with BCM, TCM and combination meter.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1
>> Refer to
NO-2
>> Refer to
. (Combination meter)
2.
CHECK COMBINATION METER BUZZER
Check combination meter buzzer.
Refer to
DLK-83, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK INTELLIGENT KEY WARNING BUZZER
Check Intelligent Key warning buzzer.
Refer to
DLK-101, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK DOOR SWITCH
Check front door switch (driver side).
Refer to
DLK-95, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CHECK INSIDE KEY ANTENNA
Check inside key antenna.
• Console: Refer to
• Luggage room: Refer to
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
CHECK INFORMATION DISPLAY
Check information display.
Refer to
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace the malfunctioning parts.
7.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
REMINDER FUNCTION DOES NOT OPERATE
DLK-771
< SYMPTOM DIAGNOSIS >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMINDER FUNCTION DOES NOT OPERATE
DOOR REQUEST SWITCH
DOOR REQUEST SWITCH : Description
INFOID:0000000010683773
Reminder function does not operate using door request switch.
DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000010683774
1.
CHECK DTC WITH BCM AND COMBINATION METER
Check that DTC is not detected with BCM and combination meter.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1
>> Refer to
NO-2
>> Refer to
. (Combination meter)
2.
CHECK “ANSWER BACK” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “ANSWER BACK” in “WORK SUPPORT” mode.
3.
Check the “ANSWER BACK” in “WORK SUPPORT”.
Refer to
DLK-676, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 5)"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “Off” in “ANSWER BACK”.
3.
CHECK “ANSWER BACK I-KEY LOCK UNLOCK” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “ANSWER BACK I-KEY LOCK UNLOCK” in “WORK SUPPORT” mode.
3.
Check the “ANSWER BACK I-KEY LOCK UNLOCK” in “WORK SUPPORT”.
Refer to
DLK-676, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 5)"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set “BUZZER”, “HORN” or “Off” in “ANSWER BACK I-KEY LOCK UNLOCK”.
4.
CHECK HAZARD FUNCTION
Check hazard function.
Refer to
DLK-741, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CHECK INTELLIGENT KEY WARNING BUZZER
Check Intelligent Key warning buzzer.
Refer to
DLK-744, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
CHECK HORN FUNCTION
Check horn function.
Refer to
SEC-173, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace the malfunctioning parts.
7.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
DLK-772
< SYMPTOM DIAGNOSIS >
[TYPE 5]
REMINDER FUNCTION DOES NOT OPERATE
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
INTELLIGENT KEY
INTELLIGENT KEY : Description
INFOID:0000000010683775
Reminder function does not operate using Intelligent Key.
INTELLIGENT KEY : Diagnosis Procedure
INFOID:0000000010683776
1.
CHECK DTC WITH BCM AND COMBINATION METER
Check that DTC is not detected with BCM and combination meter.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1
>> Refer to
NO-2
>> Refer to
. (Combination meter)
2.
CHECK “ANSWER BACK” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “ANSWER BACK” in “WORK SUPPORT” mode.
3.
Check the “ANSWER BACK” in “WORK SUPPORT”.
Refer to
DLK-676, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 5)"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “Off” in “ANSWER BACK”.
3.
CHECK “ANSWER BACK KEYLESS LOCK UNLOCK” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “ANSWER BACK KEYLESS LOCK UNLOCK” in “WORK SUPPORT” mode.
3.
Check the “ANSWER BACK KEYLESS LOCK UNLOCK” in “WORK SUPPORT”.
Refer to
DLK-676, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 5)"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set “On” or “Off” in “ANSWER BACK KEYLESS LOCK UNLOCK”.
4.
CHECK HAZARD FUNCTION
Check hazard function.
Refer to
DLK-741, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CHECK HORN FUNCTION
Check horn function.
Refer to
SEC-173, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст